Jump to content
SAU Community

Recommended Posts

Ok as most as most of you guys know recently i had to change my Lower Control Arm and Caster Rod, after getting a new set of tires, alignment and suspension check the car is starting to pull to the left (if I let go of the steering wheel it will just start going to the left) I was wondering what you guys think it is, it drives fine i took it to the midnight cruise with no dramas but its worrying me for the Buller cruise. Does anyone know of a good suspension specialist near Caulfield East? After a close examination I think I've tightened the LCA bolt too tight but it seems to be stuck now (It free spins, no amount of untightening or tightening makes it move) I'm currently getting another bolt from the guy I bought the LCA from but I just haven't had the time (as he lives in Frankston) although I dont think it will have a major influence on the steering will it?

Any input appreciated

EDIT: I have to keep the steering wheel slightly to the right for it to go straight

Link to comment
https://www.sau.com.au/forums/topic/294690-car-pulling-to-left/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Ok as most as most of you guys know recently i had to change my Lower Control Arm and Caster Rod, after getting a new set of tires, alignment and suspension check the car is starting to pull to the left (if I let go of the steering wheel it will just start going to the left) I was wondering what you guys think it is, it drives fine i took it to the midnight cruise with no dramas but its worrying me for the Buller cruise. Does anyone know of a good suspension specialist near Caulfield East? After a close examination I think I've tightened the LCA bolt too tight but it seems to be stuck now (It free spins, no amount of untightening or tightening makes it move) I'm currently getting another bolt from the guy I bought the LCA from but I just haven't had the time (as he lives in Frankston) although I dont think it will have a major influence on the steering will it?

Any input appreciated

EDIT: I have to keep the steering wheel slightly to the right for it to go straight

Maybe they didn't align it probably? Because if problems was with the things you install, wouldn't the car sway left when the steering wheel is straight? It's just a guess lol

But I'd hate to see you fall off the mountain next weekend :down:

its meant to veer to the left ever so slightly if you take your hands off the wheel

its a safety feature designed to make you not run onto the wrong side of the rd

just check how much - if in doubt goto a wheel balance / suspension place

Could it potentially be your tie rods? Even after an alignment, the settings won't stick if your tie rods are porked.

Suggest you get those looked at.

A nice place to go around East Caulfield; perhaps Pro Tek tyres? They're located on the corner of Ferntree Gully Rd and Dandenong rd. If not there, you can head down Nepean Hwy towards Nissan Brighton. Theres a place directly across from there but I'm not sure of the places name.

Good luck.

its meant to veer to the left ever so slightly if you take your hands off the wheel

its a safety feature designed to make you not run onto the wrong side of the rd

just check how much - if in doubt goto a wheel balance / suspension place

Actually, thats true. Because the roads are made to be on an angle, so water and stuff rolls off to the side. There's one way to test it, is to drive in the middle of the road (of course when there's no cars), then let go off the steering wheel lol.

Could it potentially be your tie rods? Even after an alignment, the settings won't stick if your tie rods are porked.

Suggest you get those looked at.

A nice place to go around East Caulfield; perhaps Pro Tek tyres? They're located on the corner of Ferntree Gully Rd and Dandenong rd. If not there, you can head down Nepean Hwy towards Nissan Brighton. Theres a place directly across from there but I'm not sure of the places name.

Good luck.

ProTek and tierods/ends.... sounds like a plan.

Will pull to the left on most roads due to the slope, if you run a little more castor on the left i think it is it drives straight on cambered roads.

also take into consideration tyre condition and inflation, make sure they are all even,

and possibly brakes dragging or handbrake being overadjusted on the left side

or even a dodgy wheel alignment, these 4wsteer systems need experienced ppl to do them right.

could be a stuffed Tie rod since you hit it hard enough to bend an LCA

did you get an alignment print out from the aligner,

as some places will just say, we made it as straight as we can, without showing any printouts with all the alignment settings

could be a stuffed Tie rod since you hit it hard enough to bend an LCA

did you get an alignment print out from the aligner,

as some places will just say, we made it as straight as we can, without showing any printouts with all the alignment settings

Yea man Nathan gave me the alignment print out but I dont know about this stuff, I'll go get it and post it up here to see if anyone know about it

Some comments the mechanic left after a comprehensive check:

Play in L/H Front King Pin

Play in L/H rear tie rod end and upper control arm joint

L/H ball joint rubber cover split

sounds pretty serious..........

2deg less castor on the left than right, 2mm less toe on left than right, 1deg less neg camber on the left. Normally when they can't adjust camber and castor atleast get the toe equal side to side... Take it somewhere that can give advice when they see the camber/castor is out that much with no adjustment IMO.

i see this as the issue. the .3 of a degree difference in camber on the rear is insignificant compared to the fronts overall differences.

yeah i agree with ryan,

all you have to do is just look at the final values column and compare left to right

The values should be very similar left to right

your front end is showing some major differences

take it to a suspension specialist and see if they can fix it using factory adjustments

otherwise, the problem lies deeper within the suspension mounting points which could have been damaged in the accident, or possibly a bent hub

Are you running standard (stock) suspension setup?

If you are - try to find the factory manual - it seems to have all the correct angles (specs) etc. and send it to the wheel/suspension place.

Then take the car for a run on the freeway.

Ok well the story is that I brought the car to ProTek where they said (after looking at the alignment sheet) that he thinks the guy wasn't exactly the most capable but in his defense he said that he thinks the whole suspension has been pushed back and in a bit, his suggestion was to bring it to pedders and get an aftermarket setup that would allow me to adjust and compensate for the damage, or to bring it to a specialist and see what they can do. He recommended me to Kents but of course every time I hear "panel beater" there is only one real name that comes to mind when operating on a budget (Vu) so the car is now with Vu @ DT Panels and hopefully he'll be able to get it fixed with no real dramas and at a good price

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...