Jump to content
SAU Community

Recommended Posts

Recently ive been very keen to put a cold air intake from my throttle all the way down to the k&n pod under the chassis. I got quoted $300 to get it done on my r32 gts. Before i go get it done, i need to know - do you get any performance gain out of it? ive been told otherwise...

i mean, ive been reading that the suction is based on the ECU, and not the material of the pipe and that cold air intakes can cause hydrolock

Recently ive been very keen to put a cold air intake from my throttle all the way down to the k&n pod under the chassis. I got quoted $300 to get it done on my r32 gts. Before i go get it done, i need to know - do you get any performance gain out of it? ive been told otherwise...

i mean, ive been reading that the suction is based on the ECU, and not the material of the pipe and that cold air intakes can cause hydrolock

+1 on the hydro-lock

If you put it in the wrong place and you hit a puddle or in my case your in a flooded car park you will root your engine

http://www.skylinesaustralia.com/forums/St...p;hl=hydro+lock

go to the last few posts to see all the damage, photos and everything.

Be Careful!! - in saying that i put mine in a very stupid spot, it was cold for sure but too exposed to water and to low too the ground - as far as performance, meh i didnt notice much, get someone who has done a dyno run before and after.

IMO, if you put an air pod on, you will be sucking in hot air, unless you shield it off / box it off.

I would just upgrade the panel filter in your stock air box to a high flow K&N one.

At least most of the time, cold air will be going in.

Short answer: yes, properly setup cold air intakes do give you performance gains.

Note that it is not a cold air intake simply because the kit says so or because you installed it / want it to be a cold air intake. It's a cold air intake if the intake temperature has actually decreased from what it was before, due to whatever you did to the intake.

A $300 K&N kit will do buggerall if it's still sucking in hot air from the engine bay - can actually be detrimental to performance / stall your engine in traffic on hot days. In contrast $20 worth of ducting and a properly positioned $50 filter setup the right way can do wonders.

If you're going for a pod style setup, heat shield it and have a ram pipe/ducting running up to it from a cool air source...rather than the filter located close to the ground/rain/water, where it can hydrolock as previously mentioned.

I was looking into these two things a while ago for if i make a cai. Im not sure how effective they are, I thought they would be really popular if they worked as claimed and didnt restrict the flow to much.

Bypass

http://www.modified.com/tech/0104scc_aem_a...alve/index.html

hydrashield filter

http://www.autoanything.com/air-filters/65A2582A0A0.aspx

Edited by Mendoza

also it should be said that the gains aren't that great. people go on about it being some massive performance mod and if they go up against a car without it they are going to leave it for dead. this is far from the truth. the fact that most cars these days come with some form of intake designed to suck air from a location that alloys cool air, in most cases a CAI setup will net you a gain of maybe 5kw in an extreme case, but more than likely only 1 or 2kw. where people often are misled is thay they will put a new highflow panel filter in at the same time as doing the CAI setup and think that all the gains were from the CAI.

as for the power loss from hot air, that is also made to be a bigger deal than it is. when i took my magna to the drags, my quickest ET and top speed was achieved with the snorkel to the airbox removed and it was sucking air from the engine bay. often people go a bit overboard trying to make a CAI and end up with no gain or even a loss because because they have added so much restriction that they have negated any gains from having a cooler intake air.

cara are you saying you got the tune done and the CAI, or just the CAI? cause if the tune was done at the same time then that probably has more to do with it than the CAI.

i used to have a magazine where they fitted a CAI and k&n panel filter to a car and did before and after dyno runs. don't remember too much about the article but i remember the key figure. on a car making around 125rwkw i think it was, the difference in max power with both the CAI and filter was 4kw of the stock snorkel and paper filter.

re done the piping for air intake, and had to get a tune done again cause she was running heaps rich with the new piping......

but comparing the old piping to the new one, the car has a lot more resposiveness that what it did, it wouldnt have changed anything kW was, but at least i got the resposiveness ;)

ive got mine coming from the front of the bar going up to a pod, but what has made the main difference is the piping from the pod to the throttle body.

So you are saying that the silicon piping was the key difference maker? if so, what makes you think so?

Btw, you got more photos of your car - that's very nice looking car, love the paint scheme - not sure about asian-eye headlights tho ;-)

cheers

  • 8 months later...
re done the piping for air intake, and had to get a tune done again cause she was running heaps rich with the new piping......

but comparing the old piping to the new one, the car has a lot more resposiveness that what it did, it wouldnt have changed anything kW was, but at least i got the resposiveness :P

Hey Cara how did you do your CAI piping i see some silicone and some stainless etc can you give more detail.

now this may sound like a stupid question but what happens to all the tubes goin into the stock intake pipe when you change it are they unimportant or do you need to find a way to connect them back up.

sorry for my ignorance on this topic im still learning :-)

Cheers

In my opinion,

gains are so minimal its not worth the money.

Save your money and spnd it on something more worth while.

There is very little increase in power or torque.

The only thing you'll gain is a deep growl under throttle.

If thats the only thing your looking for, just add a pod only.

CAI's have very little menefit unless your car is often working hard in hot conditions.

Edited by GTS4WD

ok, im going to go against what others are saying on here about it.

I have a full heatsheild and cai... if you want to do it yourself for about ~$50 each then it might be worth while looking in the tutorial section...

anyway. When I did it, I did notice a difference in torque and power, but very minimal... it did however increase throttle response.

It used to be with an unshielded pod as hot as the rest of the motor at the end of say a 30 minute drive. What I have noticed change the most is, you know when your car has just warmed up on a cold morning and you give it some beans and the throttle is nice and crispy... well you get that pretty much most of the drive...

I can drive the car for an hour, take the heatsheild off, which is just a little warm, and can touch the pod and it is still cold, so yes, it does make a difference.

Hot days are better for the car aswell, it still suffers from the heat, but no where near as bad...

The thing is, my car is turboed so with more power you can feel the difference more then an n/a...

If you were going to have a crack at it yourself for 100 bucks i'd say worth it, but 300, i think is a bit steep for very minimal gains on a ~100kw skyline, I would put the money to some good oil, plugs, etc or go to a workshop that tunes skylines and get them to advance your timing abit for 100 bucks, you'll gain 10kw out of that as oppose to 1-2kw

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...