Jump to content
SAU Community

Recommended Posts

something seems a bit suss about this. you'd think that putting it into neutral would work. i'm guessing he didn't try pushing the brakes when/if he put it into neutral.

Yep. First thing I said when I heard it. Considering the news was saying that he went the length of Eastlink with the malfunction.... just sounds waaaay too sus to me.

+1 to suss. Neutral + brakes and then down gears regardless of transmission type. The other thing that doesn't make sense to me is why the ignition could not be turned off.

Anyone have any ideas why the ignition off wouldn't work?

The Cruise control is turned off by the brake light switch behind the peddle. As most drivers don't service the vehicles enough or replace globes or check that vehicle indications are working. You may well find Ford will look at the car and find a faulty brake switch. Which is a servable part on most Fords.

The driver in this case had obviously panic'd and has never had an advanced driving course for say when the accelerator becomes stuck open. Slame car to neutral, carress brakes, slight use of the hand brake to slow gradually to a stop. As he was on eastlink and the section near Wellinigton road is up hill the car should have been able to be slowed in this part of the tollway quickly.

I believe the driver is 75% at fault in this instance.

I think its great that he called Ford and got put on hold, then called the police.

He also stopped by hitting the brakes extremely hard and using the handbrake at the end....why not at the start?

Oh, and unsure about the neutral thing, there is another thread somewhere on this forum, same topic :ninja:

+1 to suss. Neutral + brakes and then down gears regardless of transmission type. The other thing that doesn't make sense to me is why the ignition could not be turned off.

Anyone have any ideas why the ignition off wouldn't work?

allot of vehicles cannot be turned off unless the car is either at idle or in park gear for automatics.

But the gears thing is obvious, the guys an idiot, he complained that the gear button wouldn't depress, but you dont need to press that button to throw it into neutral....

also did anybody notice that in the pics of the car after it had stopped there are no skid/tyre marks on the road????? for such high speeds and handbraking the explorer leaves no marks lol

it took 40 kms and a pending crash to try and apply the handbrake and normal brakes at the same time... what the hell were they doing the rest of the time?

chatting about fashion probably...

Agree, complete and utter stupidity or an attempt of 15 mins of fame

The more electronics and cpu's control, the more chance of something failing with the driver unable to do anything about it.

I am not happy with the electronic throttle already in my car, now I just want to rip it out "in case". Whats wrong with a cable and spring anyway? Surely more reliable than a stepper motor and some plastic gears.

I will be interested to see the outcome of this if Ford don't silence everyone involved.

the explorer has the ability to lock the transmission however im not sure if it does it when cruise control is turned on. normally as soon as the brakes are touched, the cruise control goes off.

so, with a heavy and powerful car with cruise control stuck on and no way to put it into neutral (assuming its auto), it would be hard to stop. however, not 30mins to stop.

parents own a '04 V8 explorer.

Even assuming it's automatic why wouldn't it be able to be put into neutral?

the ablility for any car made and imported by a major manufacturer in the last 15 years explains that an automatic transmission MUST be able to slide into neutral without haveing to press buttons or complicated sequences as explained by the ADR just for this reason.

I'll be very surprised if this guy isn't on the news again for being a drop kick....

also worst come to worst, kick the gear lever if its stuck, the worst that will happen is you completely destroy all the teeth in a certain gear and the car will have no drive...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...