Jump to content
SAU Community

Recommended Posts

Hi all!

The forum has been lacking a DIY for putting your 4WD stag into RWD mode.

Firstly theirs a number of reasons you might want to:

  • 2wd dyno runs
  • Saving coin on the tuner pulling it out
  • Making yourself feel better due to less power loss from awd system
  • Skids
  • Burning up tyres before installing new ones
  • Any other stupid reasons you can think off......

The reason I'm pulling it is we've got a dyno day tomorrow and only mods since last power run on a 2wd dyno was shift kit and a 3' highflow cat (used to have gutted 2.5')... So im really trying to work out if the kits done anything power wise (yes I will report after the day)

It takes roughly 45 minutes, perhaps allow an hour for first timers

Tools required:

  • 4 Jack Stands
  • 13mm Ring Spanner
  • Trolley Jack
  • 12mm socket on ratchet and whatever adaptors you need for your setup
  • King G Overals :P (for keeping clean while rolling around on dirty garage floor)

20740_1303800590157_1084756809_30948537_6560848_n.jpg

Method:

1. Start by jacking up your car get it so all 4 wheels are off the ground by 3 or so inches

20740_1303800430153_1084756809_30948533_5364533_n.jpg

2. ENSURE you give the car a good shaking once its up on stands to ensure its nice and stable cos your going to be working under it!

3. Get under and locate your front drive shaft It comes out of the transfer case and has four bolts that go into the front diff

20740_1303800470154_1084756809_30948534_5707590_n.jpg

4. Go inside car and release park brake and put it in N

5. Jump back underneath and watch the shaft and spin one of the front wheels to spin the shaft to where its nice and easy to get at each bolt, you need to move the shaft for each bolt. I do them in this position

20740_1303800550156_1084756809_30948536_6430178_n.jpg

6. Take your socket and 12mm and put it on the bolt head (side of bolt towards rear of car) THE BOLTS AND NUTS ARE NOT REALLY HARD AND ROUND EASILY SO BE CAREFUL!

7. Try and give it a few spins to get it all moving you may be lucky and it may crack and you dont even need to use the 13mm to hold the nut still to undo them

8. Once you have all four bolts out pull the front of the shaft down and then pull and jiggle it forward. The rear is just a spline set-up thats all sealed so it will come out with a bit of pulling.

20740_1303800510155_1084756809_30948535_2315822_n.jpg

9. Drop the car, do a lap around the block with a bit of a heavy foot where you shouldn't (aka out of a corner) and you will soon be able to tell its in RWD. No fuses need to be pulled. You will not get any fault lights or anything. This is the only SAFE way to run in RWD to avoid frying clutch packs ect...

Installation is simply the reverse. Dont need to do the shaft nuts up super super tight. Again THE BOLTS AND NUTS ARE NOT REALLY HARD AND ROUND EASILY SO BE CAREFUL!

Hope this helps someone.

Cheers,

Chris

  • Like 1
  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/304189-diy-4wd-to-rwd/
Share on other sites

You need to pull the 4wd fuse in the fusebox next to the battery.

"NEED" I think is the wrong word.. I guess you could but Ive had it out before and spoken to tuners and its not necessary. Ohhh and also a mechanic that had his shaft out on his OWN stagea for about 6months with no fuse removal and NO issues

Link to comment
https://www.sau.com.au/forums/topic/304189-diy-4wd-to-rwd/#findComment-5038228
Share on other sites

Great howto thanks Chris! Now I have a better idea about what's involved and it looks reasonably straight-forward... as usual, the hardest part is getting the damn car far enough off the ground safely!

Whenever the mech' removes mine he always removes the (big, 30A) fuse. It's not hard - takes 5 seconds or so and has at least these advantages that I can think of:

- saves wear on the ATTESA pump by not running it all the time

- lets the system know that it's in RWD mode (and the driver by illuminating the 4wd warning light)

- stops that infernal clicking! (the dreaded ATTESA relay)

...so why not do it and take advantage of the benefits or however SK puts it... just my thoughts :P

Edited by DaveB
Link to comment
https://www.sau.com.au/forums/topic/304189-diy-4wd-to-rwd/#findComment-5038334
Share on other sites

Pulling the fuse is not enough on the Stagea you have to remove the front drivshaft. The Attessa is different from that on the R32 where pulling the fuse was all you had to do.

ah k i use to have a 32gtr wish it was easy as that

Link to comment
https://www.sau.com.au/forums/topic/304189-diy-4wd-to-rwd/#findComment-5038861
Share on other sites

  • 2 weeks later...
Ok for those wondering the shift kit and cat seemed to up the rwkw by 25. This is also with a tiny bit less boost. very pleased awesome day on the dyno thanks rodders!

no worries chris,had a few sms/pm's of thanks and im glad everyone had a good day and enjoyed it. i may organise another in due time

will catch up with you soon buddy!

Link to comment
https://www.sau.com.au/forums/topic/304189-diy-4wd-to-rwd/#findComment-5062629
Share on other sites

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...