Jump to content
SAU Community

Recommended Posts

Yo yo, I havn't adjusted it at all cost me like 300 all up with a wheel alignment and height adjustment to lowest legal, they setup the stiffness on what you say I told them I will be using it mainly for street and a bit of track work so they did so quite well I think (traction tyres in rowville) so couldn't answer your question apart from recommending to get someone else to do it, because they gave me a sheet with camber % and all these different readings which I had NFI about, and even if I did how the hell would one get into that much detail in there own garage with a jack.

fair enough,im getting mine done on thursday along with a full service, belts and everything so im looking forward to getting that done and knowing my car will be very healthy.

what's the industry term for the printing on the NS hoodies? don't think it's screen printing, it's more like a heat transfer style...

I need to find a place that can do it..

silk screening?

thermal transfer?

what's the industry term for the printing on the NS hoodies? don't think it's screen printing, it's more like a heat transfer style...

I need to find a place that can do it..

Goto one of those "T-Shirt" bar places and they could transfer the image on for you...

silk screening?

thermal transfer?

I'm thinking it's thermal/heat transfer style, but the singlets I've got from last years pre season just have this certain feel about them (where the printing is)....I'll have to take that to a few places as a sample and hope they can match it

Not exactly on the scene with my current vehicle

need to man up and get a gtr then :D

reporting for duty.

and u aint no gtst sedan stop false advertising

haha i used to be cool :blink:

now i just drive a yellow lancer

i hope so - was a very rough start / idle too

first time its ever done it

noticed when I turned the headlights on i could hear a bit of a whining from the engine same when i pushed brake in a tiny bit :S :D

which i have never heard before also

Lol Leigh you stooge. I'll install a head unit for you. It's a piece of piss. Already did 3x r33, 2x r34, alfies celica and prob more lol

lol i know how to do it just needed the wiring diagram :huh:

had the head unit in my closet for a month so i figure ill put it in and do some cheap speakers at the same time, cbf with a good sound system anymore i only use it every now and then for a few tunes and dont tend to crank it

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...