Jump to content
SAU Community

Recommended Posts

I think the black looks pretty sick. Funky, got any more photos of black advans?

If anyone wants to chop my pic in photoshop, by all means go ahead as I am technologically retarded.

nope, rules are you have to read the whole thread before you post

hahahaha...sif...i read couple of the newer posts and post anything i have to say...cbf reading so much..even the last page...lol

This is correct

Sadly, you will be pleased to know that I just clicked through the whole lot of the pages... gee you guys can talk some shit :D

you can buy new ones maybe?

Nah, im going overseas soon so need to save mucho casho. Plus I quite like the idea of a hover-skyline.

well its true i do touch myself at night, infact im touching myself while im typing this :P

Hehehe.

Incredible, I saw you today in your yellow evo pulling out of the united servo in Wallan. Would have been around 3:30-4:00? Couldn't believe it lol.

haha really?

farking kents charging $1.50 a litre atm :(

hows it look? :P

hmm so i tried to put on an r33 gtst catback on my 34 gtt, hangers line up (just) and it sits nicely. but theres now a 15cm gap between the end flange and the front pipe flange.

problem 1 - cat wont fit in that gap

problem 2 - both flanges are on the same angle, so even if the cat fit, 1 of the flanges wont line up

solution - get a 15cm decat pipe made with both end flanges on the same angle

incase anyone was curious...

f**k im so helpful

Done,

The culprit was a bolt stuck on thorttle cable (rear of the holder bit on 26)... Here I were worrying about being carless and at least $500 out of pocket...

Damn cars, time to take up new hobby!

so it wasnt a vacuum leak afterall? :domokun:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...