Jump to content
SAU Community

Recommended Posts

thinking about going a 3.0 in mine, but with the 2835 pros...

response will be phenominal

Do it?

Just slap 30 bottom end and whack your head in and take me for a ride and see if it scares me?

يقخلرث شمم فاث صشغ فخ ؤقشىلاخعقىث فخ حهؤنعح يشيس 740هم لاثشةثقو بشقن هف صشس يقشهىهىل

damn, parents left it on arab lang

anyways, draining drive to cranny and back to pickup dads e38 740il... needs spacers and an exhaust

Edited by Mohsen

thinking going cast aftermarket pistons etc in a 3.0 with my 25 head/oilpump/turbo/inj etc as i cant afford a fully forged jobby...

figure if i get a wrecker motor it'll be cast pistons anyway, and they'll be old, so it should be stronger than a wrecker, and better

and it's an evo 8. better off getting an evo 7 RS or getting a locally delivered evo 9. why waste money on the middle child? only evo 8 worth getting is an Evo 8 MR, anything less is just a waste of money.

33581520002_large.jpg

EVO 8 MR FQ400!

Is all win! :D

damn al's car was impressive

3 litre big single is where it's at

flat out power, response, oodles of torque and all round nice engine setup

But there Is always something wrong with his car. Rb30 = lots of breaking lol. So need big $ to maintain it.

  • Nope 1
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...