Jump to content
SAU Community

Recommended Posts

has it always been like that? Did the seller say it had diff turbos? If he didnt why would u not say so to warrant higher sale price? Easies way is to check the markings on the compressor cover. But u said coilpacks are f**ked? When does it misfire

.

has it always been like that? Did the seller say it had diff turbos? If he didnt why would u not say so to warrant higher sale price? Easies way is to check the markings on the compressor cover. But u said coilpacks are f**ked? When does it misfire

.

to be honest cant remember how long its been like this but as long as I can remember, basically got the car imported through a private importer but he didn't know of any changed turbos as such and being my first turbo car it wasn't until i actually looked at dyno threads that i realized its hitting full boost very late the car misfires coming onto boost or generally struggles at low revs when warming up especially changed plugs and no change so waiting for splitfires now.. but as Hamish said waiting for nengun is >_<

how hard is it to check markings what shit do i have to take off

and if it were a leak wouldn't the car not make it to 1 bar on my gauge?

nah it will still reach target, just laggy as the pressure leaks constantly during build. Mine did the same just a touch laggy and lacked some zest

ah yeh makes sense will go have a look at a few things

Guess what? Something you guys will never think I would do :O. Greddy type s coilovers (hamishs recommendation) ordered from jap land. Then some whiteline adjustable sway bars are next :D

Nice man, i got swaybars on their way too :banana:

Are you still going for an e85 tune?

I would love to do more low! But then that would have to park the car outside cuz it won't get into the secure parking in my appartment. :( there will be heaps more low when I get my own place with a good driveway :)

I would love to do more low! But then that would have to park the car outside cuz it won't get into the secure parking in my appartment. :( there will be heaps more low when I get my own place with a good driveway :)

by all means get more low. Then i will take the car spot!

:D :D

nah it will still reach target, just laggy as the pressure leaks constantly during build. Mine did the same just a touch laggy and lacked some zest

eh tightened and checked every clamp i could still no change fml, maybe ill just wait for coilpacks and see if they make any difference

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...