Jump to content
SAU Community

Recommended Posts

On 3/24/2018 at 5:37 PM, Lithium said:

Nice - what setup do you have that on? How is performance?

Quoted Lith because he loves a oil leaking precision... 9.609 @ 146.10mph last night at the drags

Not bad for the baby 62mm, only got one pass and then got the boot

18 hours ago, usmair said:

congrats on your time. very impressive!

 

  • Like 3
  • Haha 1
4 minutes ago, SimonR32 said:

Quoted Lith because he loves a oil leaking precision... 9.609 @ 146.10mph last night at the drags

Not bad for the baby 62mm, only got one pass and then got the boot

 

Yes..

 A rather mysterious Piglet has been keeping me up to date on the bacon you've been making. Absolutely huge effort - I am blown away... There is so much to be impressed with in regards to that result.

How confident are you that the same parts list you have would achieve the sake results? 

  • Like 1
On 3/29/2018 at 7:53 PM, SimonR32 said:

I think that anyone could do it with the right knowledge and skills, but it's not a simple slap on a 6262 and do a 9.6

Yeah obviously - though the power to pull high 140mph trap speeds is no joke!   Funny, I was reading a thread with someone running a 6466 on a Supra and "on kill" they ran a few mid/high 9s at high 140mph traps before snapping a turbine shaft.  Your 6262 is punching high!

  • 2 weeks later...
  • 2 weeks later...

Here's a 6266CEA on my 30DET @ 24psi, held across 4200-7200rpm.  All basic build stuff, engine included.  8.4:1 CR, 265 degree 8.9mm fixed cams. Single scroll 0.84A/R on a 6boost manifold, 50mm gate plumbed back.  Running on petrol.

Timing scatter is currently an issue, did impact on tune/output so there's gains simply from fixing that (in progress now before the next event)

20180424_234850.jpg

20180426_104110.jpg

Edited by Dale FZ1
  • Like 2
40 minutes ago, Dale FZ1 said:

Here's a 6266CEA on my 30DET @ 24psi, held across 4200-7200rpm.  All basic build stuff, engine included.  8.4:1 CR, 265 degree 8.9mm fixed cams. Single scroll 0.84A/R on a 6boost manifold, 50mm gate plumbed back.  Running on petrol.

Timing scatter is currently an issue, did impact on tune/output so there's gains simply from fixing that (in progress now before the next event)

20180424_234850.jpg

 

RB26 Head?  Will you be getting an E85 tune?  Looks like it's holding power quite well to redline currently, will be interesting to see it does with more stable triggering.   There is an outfit in NZ who do a very affordable cam trigger setup (but not using the flimsy stock Nissan drive) which fixes this kind of thing with the stock cam angle sensor configuration without going 10/10ths on a crank trigger setup, if you haven't gone there yet and were wanting a reliable trigger setup without going 4 digit costs.

9 hours ago, Lithium said:

RB26 Head?  Will you be getting an E85 tune?  Looks like it's holding power quite well to redline currently, will be interesting to see it does with more stable triggering.   There is an outfit in NZ who do a very affordable cam trigger setup (but not using the flimsy stock Nissan drive) which fixes this kind of thing with the stock cam angle sensor configuration without going 10/10ths on a crank trigger setup, if you haven't gone there yet and were wanting a reliable trigger setup without going 4 digit costs.

No, just a 25 head with hydraulic lifters and upgraded springs + minor exhaust port adjustments.  The whole thing is loafing along, quite a bit more to extract if desired.

We'll resolve the triggering prior to the next event at end of May, and get it on the rollers at some stage just to validate the improvement.  Going with the cam trigger setup you mention, interested to see the difference in timing logs.

Probably staying with petrol at this point simply because it's not short on stick for what I need the car to do.  And I avoid the inevitable need to go with further fuel system upgrades.  Money better spent on tyres/event entry and actual seat time :)

  • Like 1
  • 2 weeks later...

Quick run on the dyno today just to have look at things, no tuning has been done with this turbo setup but was previously tuned with an unknown high flow on 14psi.

Currently does not have the  boost controller plumbed up and has 14psi gate pressure with a turbosmart 50mm on a 6boost manifold and 5862 turbo.

The dyno graph shows rpm about 300rpm different to last time it was on there, makes it look a bit laggy but it feels not that much different down low from the high flow and is a completely  different car now through the mid range and up top. Currently has 11 degrees of timing from 4500 rpm and up at 18psi.

Its given me a bit of motivation to get the new motor together and  get it on e85 and turn it up

20180507_135850_resized.thumb.jpg.0520440a1920493dbcf195520395552f.jpg

  • Like 2

Not a Skyline but this is a street engine RB26 (BC 2.8L Stroker kit) with a TH400 box, made 915whp through the auto and 1070whp through a manual on 35psi with a Precision 8285 (1.12 A/R) - sounds better than a mangmang. 

Cranked it to 40psi next meeting and cracked the factory block like a spider web, the car sadly hit the wall hard.

 

Also as a veteran of this thread I'm putting my PTE knowledge to a bit more use these days, I can help out any SAU Members interested in ordering Precision Turbochargers off my website.

www.makemegofast.com

 

  • 2 weeks later...
On 3/24/2018 at 2:37 AM, Lithium said:

Nice - what setup do you have that on? How is performance?

Its on a Forged RB30, ported head Tomei 272's E85 

I like the turbo so far good response for what it is and it seems to make decent power.. Cant beat it for the money..

I sold my Precision after Precision rebuilt it and bought 2 Borg warners!! haha

3 minutes ago, mitchum said:

Its on a Forged RB30, ported head Tomei 272's E85 

I like the turbo so far good response for what it is and it seems to make decent power.. Cant beat it for the money..

I sold my Precision after Precision rebuilt it and bought 2 Borg warners!! haha

Nice - any more specifics?  Been quite curious about the SX-E turbos and a few RBs seem to have them but no dyno sheets or hardly even any numbers, yours included now haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...