Jump to content
SAU Community

Recommended Posts

  • Replies 139
  • Created
  • Last Reply

Top Posters In This Topic

Have a read at hypergear's latest update with the ATR43g3. Very reasonable response for 303rwkws. And that is internal gated on a stock standard engine with all factory gears.

That is fairly false, while a good upgrade the majority of results see no where near 300rwkw from the high flows.

Most people see 230-240rwkw from a high flow, dyno results thread to back.

That is fairly false, while a good upgrade the majority of results see no where near 300rwkw from the high flows.

Most people see 230-240rwkw from a high flow, dyno results thread to back.

That depends on the type of rear housing that we get to do the high flow as well as the combination of wheel we use refer to customer's driving ability. I've personally tested a .63 PU high flow maxed at 295rwkws, Roller dyno, 98 fuel, tuned by Dr.drift.

How ever the ATR43G3 mentioned is a brand new turbo that is made and proven for 300rwkws application, with 65kws more mid range then the KKR560. Plus controlled run is based on fully standard setup without boost controller or any thing that could advance its original response and power behavior.

That depends on the type of rear housing that we get to do the high flow as well as the combination of wheel we use refer to customer's driving ability. I've personally tested a .63 PU high flow maxed at 295rwkws, Roller dyno, 98 fuel, tuned by Dr.drift.

How ever the ATR43G3 mentioned is a brand new turbo that is made and proven for 300rwkws application, with 50kws more mid range then the KKR560. Plus controlled run is based on fully standard setup without boost controller or any thing that could advance its original response and power behavior.

yes very good result, these figures are with an aftermarket comp housing, chra and rear housing.... , so as stao said, those are a completely aftermarket turbo... not a highflow

what boost tho? the 3076 will do same power and response times... but less psi needed to make same power.

its not fair? on who? haha as i said ive had both turbos on rb25's so just posting my experiences.

Its not fair on the poor old 3071 :D

I am challenging this statement:

"what boost tho? the 3076 will do same power and response times... but less psi needed to make same power. "

A 3071 will have better response than a 3076 with same rear housing. The 3076 will have more top end power.

true.. i should have been clearer. When we're dealing with the 3071 with a cropped ex wheel and a OP6 style or AVO style rear housing and internal wastegate as opposed to the 60mm garret 4bolt ex gate housing... the 3076 comes out top there.

the 3071 with the same garret 4 bolt rear housing is a different story since it has a 71mm wheel as opposed to 76 it will spool earlier for sure.

just after a rough figure, but 'roughly' what does it cost to highflow and rebuild the rb25 turbos?

Bush bearing combo would be 800-1200

Proper ball bearing unit would be 1600-2200

Many factors involved from who does it, what specs and so on.

Personally, I'd go the ball bearing everytime.

i have a apexi ax53B70, had it tuned the other day and made 240kw on 18psi with 555cc injectors, pfc, z32, 3" exhaust, fmic. but was told i wont get any more out of it. pretty annoyed as i spent just under 2k on it and was told i would see 250 with ease. although i am very happy with the response :D

how much does a 3071 go for?

I got mine from Kudos Motorsports. I wanted the whole kit (dump, lines etc) and theirs was the cheapest i could find

Yeah just had a look, not a bad deal.

ooooo it has an option for the anti-surge compressor housing. did you get that?

Do you have a dyno sheet? I couldnt find one of yours in the dyno thread?

Edited by Harey
Yeah just had a look, not a bad deal.

ooooo it has an option for the anti-surge compressor housing. did you get that?

Do you have a dyno sheet? I couldnt find one of yours in the dyno thread?

no i didn't want to fab up a massive 4" intake pipe, I managed to squeeze my standard one (with metal insert) over the smaller mouth.

dyno sheet is a few weeks away :)

no i didn't want to fab up a massive 4" intake pipe, I managed to squeeze my standard one (with metal insert) over the smaller mouth.

dyno sheet is a few weeks away :)

ah yeah fair enough. its also quite a few extra dollars!

If you want the anti surge compressor housing your prob better off getting the 3076 as that comes with one for no extra dollars.

Keen to see the dyno sheet!

Ah yeah didnt think about that. Once you have a 4" intake, the 3" afm will become a restriction and also annoying changing diameters if you did leave it there.

What options are there to remain with a 3" intake. I know simon you will recommend the 4" intake but think about it from a stealth on the street point of view. Is it possible to get an anti surge housing with a 3" intake on a GT30?

I've got an rb20 turbo highflowed by GCG on my rb25, makes full boost almost the same as a standard turbo but it pulls very hard even on 12psi around 200rwkw. Is currently being tuned with gtr injectors and all that jazz, hoping to see 240kw with almost standard response and spool times. For a street car it is all about response.

Only thing I don't like about the turbo is the service from gcg, if anything goes wrong you will be blamed for it and have to fork out for the bill.

Edited by Rolls
I've got an rb20 turbo highflowed by GCG on my rb25, makes full boost almost the same as a standard turbo but it pulls very hard even on 12psi around 200rwkw. Is currently being tuned with gtr injectors and all that jazz, hoping to see 240kw with almost standard response and spool times. For a street car it is all about response.

Only thing I don't like about the turbo is the service from gcg, if anything goes wrong you will be blamed for it and have to fork out for the bill.

I dont understand, how is that related to "R33 Gts-t Turbo Recommendation, most responsive for 275rwkw"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...