Jump to content
SAU Community

18x9.5+25 On The Front Of My R32 Gtst?

Brad_32
 Share

Recommended Posts

Brad_32 Enthusiast

Brad_32

Posted
  • Author
Posted

Looking at 225/40's on the front and 235/40's on the rear! Was

thinkin +25 cos wasnt sure how much camber i will need run gunna roll the gaurds though! Gettin +20 on the rear! Would the front tuck in u reckon?

Roy Grand Master

Roy

Posted
Posted
Go the +20 all round.

9.5s are not too wide for the car.

What size tyres are you looking to run on it?

Sorry, if its a GTSt with std guards, even if the insides are rolled then its my experience that sized rim will not have a hope in hell of fitting on an R32 GTSt

At best you will get a 9" +28 or so on the front and a 9.5" + 36 or so on the rear. Even that will fill out the guiards and probably rub depending on ride height and tyres used.

A far better bet for a decent stance is 8.5" +30 fronts and 9" +30 rear. For the size tyre you want to run then they will fit that sized rubber better too.

I have very heavily pumped guards on my car and here is a pic of it with 350/340mm ride height and R34 GTR rims which a 9" + 30 all round They clear nicely with no rubbing. But you are talkign rims that are about 12mm wider and with a further 10mm offset. No way i can see them fitting with std guards!

19871_340712444740_606454740_4925665_2915896_n.jpg

19871_340709514740_606454740_4925653_7614877_n.jpg

Brad_32 Enthusiast

Brad_32

Posted
  • Author
Posted

One of my mates got a 32 gtst aswell hes got 17x9+17 all round with in gaurds taken out and gaurds rolled! So im thinking more along the lines of 18x8.5+17 on the front! And 18x9.5+20 on the rear! Would that work! With 225/40's on the front and 235/40's on the rear!

  • 3 months later...
Gts-t Grand Master

Gts-t

Posted
Posted
Sorry, if its a GTSt with std guards, even if the insides are rolled then its my experience that sized rim will not have a hope in hell of fitting on an R32 GTSt

At best you will get a 9" +28 or so on the front and a 9.5" + 36 or so on the rear. Even that will fill out the guiards and probably rub depending on ride height and tyres used.

A far better bet for a decent stance is 8.5" +30 fronts and 9" +30 rear. For the size tyre you want to run then they will fit that sized rubber better too.

I have very heavily pumped guards on my car and here is a pic of it with 350/340mm ride height and R34 GTR rims which a 9" + 30 all round They clear nicely with no rubbing. But you are talkign rims that are about 12mm wider and with a further 10mm offset. No way i can see them fitting with std guards!

19871_340712444740_606454740_4925665_2915896_n.jpg

19871_340709514740_606454740_4925653_7614877_n.jpg

Hey roy,

what size tyres are u running there?

cheers mick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...