Jump to content
SAU Community

Recommended Posts

  • Replies 340
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Hey man. $5 for the RB26DETT. PM me if you are interested. Free postage would sweeten the deal considerably.

Anyways seriously, when I was young about 4 years ago I ploughed my dads car through a fence tryin to get some sideways action. Noone could imagine the shame of having to knock on that persons door saying ur the one who did it. Never since that day have I tried anymore wreckless drifting or tryin to get sideways. It just too easy for something to go wrong. Some people learn the hard way, and some even harder, but unfortunatly, thats the way it is...

Gluck with everything.

the previous car i had before was a 355 xcop vt commodore.. rid that off.

now its this r33 and i hope my r32 wont be ridden off ...

the reason why there was all wires near the boost gauge ( as you can see it was a gauge lieng around) was becasue my wires were getting fixed about 10 minutes before the accident. ill have full spec details on the car (images) .

i have had ylwgtr2 to come over and have a look with his professional assitance i now have plans on what im doing to get this beast back on the streets

thanks for all the flaming and i appreciate the people wishing me luck next time.

Cheers

You are a complete and utter tool mate, I am glad that you are ok, and no one was hurt or police were not involved.

I can't afford a GTR, and you go and write one off? plus this is the second? I hope the first one wasn't a GTR aswell.

From now on you should be banished from owning a nissan period! stick to Holdens, no matter how many you wreck, they will keep pumping them out of the factory until people stop buying them

Age 20 and good experience in driving.  

Sorry buddy, but unless you do as much milage as a taxi driver there is NO way you could have enough km's under your wheels to be an experienced driver.

 

Dennis, you're a menace. And the roads will be a little bit safer until you are mobile again. Hopefully a little older and wiser and a lot lower powered. Something like a Datto 1200 would be good methinks.

Damn.. Having alot of Km's under their belt --> experienced? Taxi drivers are one of the worst drivers out there!

Also.. doesn't Melb have a law which states P platers aren't allowed to drive High Performance cars [especially with turbos]?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...