Jump to content
SAU Community

Recommended Posts

some people are holders of said key :woot:

Manildra (Fueltown) E85 all the way baby! :laugh::)

I will prob use Caltex E85 in the warmer months, but only once Trent has had a check over it on the dyno with the fuel in. Even the variance between United and Fueltown needed a little tweaking.

But i reckon get something installed in the tank to monitor ethanol levels and get an ECU to modify accordingly (interpolate between two+ maps). Basically how the the flex-fuel cars work. Just need a good enough ecu i guess.

  • 1 year later...
  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

How has this all progressed? Lots of loose ends, posting here for Googleability. Can't seem to find much info from the Google.

Where can I find current E85 prices?

How has the price/economy of it changed? (I don't drive currently so I don't know the prices)

Have any people noticed any ups and downs after an extra year of use?

Edited by jukic.j

So it's about 25c cheaper but about 30% more fuel is used unless I muddled that figure?

Don't forget to add 15% more HP into the equation.

Heard a rumour that United is going to equip more servos with E85. Any truth in that or is it simply just a rumour?

Would love to get the 33 on E85 full-time but the lack of nearby servos that stock it worries me lol

More, 50-70c

United E85 - 97c

BP98 - $1.60

$1.60? There do you fill up :O

I paid i think $1.45 the other day, might have been less. ULP on the usual good days has been ~$1.25 so it wasn't too much more.

But i reckon get something installed in the tank to monitor ethanol levels and get an ECU to modify accordingly (interpolate between two+ maps). Basically how the the flex-fuel cars work. Just need a good enough ecu i guess.

hahahahah.... indeed.

Melbourne is quite spoilt for E85 outlets - United has quite a few now, it's a pity the Caltex roll-out seems to have stalled a bit though. Don't really care though, as you're better off running United anyway.

United in Scoresby has E85 that wasn't on the website last time i looked too.

Yeah I think I'm going to run E85 too, well at least look into it seriously. I'm pretty spoilt for choice with stations around me (Caltex and United).

Just not sure how much more efficient it'll be. Still I'm finding that I'm paying around 1.45-1.54 for ULP. Dunno where some

Of you blokes are getting those mint prices! :D

Where are you located? There's heaps of E85 servos around me

The 33 stays in Berwick most of the time but also keep it in Frankston occasionally too.

Only Uniteds I know of that stock around those two areas are Patto Lakes and Hallam :unsure:

The 33 stays in Berwick most of the time but also keep it in Frankston occasionally too.

Only Uniteds I know of that stock around those two areas are Patto Lakes and Hallam :unsure:

Hallan close enough !!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...