Jump to content
SAU Community

Recommended Posts

I got a r33 gts............

I'll be buying a rb25det engine off justjap auto and putting it in my car......will it be a direct conversion...or are there any other things to change???

please advise me...

  • 2 months later...
  • 2 weeks later...

Well the reason I said that was because when I was looking at doing it the engine package was $6-$7K...they're a lot more reasonable now..but it's still going to be at elast $2K to put it in.

The best option is to make an RB30DET out of your N/A engine

Great thread,

I too made the same mistake, that is buying a N/A skyline except mine is and R33 GTS. I am desparate to turbo my engine, however my local mechanic has told me that you cannot turbo the N/A....that is without ruining the engine! Reading this discussion has helped me see what can be done to the engine, with a low cost outlay and surprising gains, Thank you!

However I have a couple of questions,

How does the car now drive?

Is it as reliable as the N/A?

Are you sure that the modifications will not damage your engine?

cannot wait to get my project Turbo underway. :flamed: :flamed:

DanielWilliam: The car currently pulls harder than a stock GTS..this is with the crappy N/A exhaust still in place and running 6.5psi that is probably down to the higher compression :(

I've had the turbo on my car for about 50,000Ks now and nothing has been damaged in that time, from a reliability point of view I think that's great. If the tune is good, you should have no problems...just don't expect to be able to cram 14psi in and you'll be fine.

Great to here that Dan,

It has put to rest the only real concern I had after reading the thread (the longterm future of the engine).

Sounds like the car goes real hard compared to the N/A You had and I have now, mine came with a full Trust exhaust out of Japan which will hopefully complement the turbo well. All I have to do now is get the funds together now and I can start the project.

I guess it is like you said tuning is the difference the car will run well and hard with some dollars in the tuning side of the car!

I will keep you informed to how my conversion comes along. I have some pics of the car in its current state in my gallery.

Cheers mate

If anyone is interested I have everything you need to do this swap

Off an RB25DET

Exhaust manifold

Turbo (No play)

Oil/Water lines

std dump pipe

Inlet manifold/Plenum

Fuel Rail and injectors

If anyone is interested in these PM me and i can send you pics

reason why i am getting rid of them, upgraded to GReddy plenum and getting top mount turbo setup

That list could make my shopping very easy!

That stuff is exactly what I am shopping for at the moment, what sort of condition is the lot in? whats your location in relation to Newcastle? Also with the condition of the parts in mind what is your best price?

Cheers :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...