Jump to content
SAU Community

Recommended Posts

People get far too caught up in whole "turbos make more horsepower" factor. Torque is loads more fun IMO. Peak power produced is only one side of things. I think of turbos as kid of the same as a big cam. You need to use lots of revs to get the power out of them. With my blower the instant boost quickly smooths out the big (blower friendly grind) cam I also run. I can waste turbo cars out of the hole at the drags. But at the other end they start to pull me in.

most poeple shun blowers cos unless they shell out moonbeams for a kit, it's not bolt on and go.

Given the screw blower my CA is getting can support 2.2 bar, but the time an equivelent turbo has spooled up I'll be a spec on the horizon.

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey the thread title says "for motorsport". My comment stands, turbos for motorsport. Unless improperly sized a turbo will be very effective

For OEM use either tiny turbos or a supercharger are the way to go for sure. no-one likes a factory car with lag.

Aftermarket use is totally different again and depends on your goals.

Having built plenty of supercharged falcon/commodores, i dont really rate them. A centrifical blower has a boost curve that goes up linearly, the more you rev it the more boost. Unfortunately that means if you want 15psi at 7500, you have to gear it then live with 10psi at 5000, which means you are close to 100rwkw behind a similarly sized tuebo setup at those revs.

Centrifugal blowers got you out of the hole, but are horribly inefficient, power hungry and once again if you want top end you need a blower the size of the slab of beer your wife drinks nightly.

To me the question isn't supercharge V's turbocharge, it's what's wrong with today's motor engineers that they can't sort out a reliable high performance engine driven turbocharger.

They've been around in very large HP applications forever, but I've never seen the technology transferred to the auto industry.

This VW monstrosity could have been done so much better/easier/simpler with an engine driven turbo.

http://www.greencarcongress.com/2005/08/inside_vws_new_.html

On the topic of supercharger versus turbocharger efficiency, there is some misleading information here...remember that off boost a turbocharger is very restrictive to engine breathing and the engine is operating at low compression (therefore wasting combustion) for 1/3 of the rev range, where we spend most of our time driving. The only time they can be considered efficient is when they are on boost. And even then, they are considered thermodynamically inefficient despite producing lots of power. So a supercharger isn't the only one that is wasting/draining energy on the constant, and the exhaust side of things is never restricted. In fact, in the lower rev ranges it is more efficient than a turbocharger.

You need to think of the comparison as linear versus non linear power production. Both have their advantages and disadvantages.

^^ agree, in the sense that turbos don't give you "free energy" by harvesting exhaust gases. you do have a penalty and that penalty is in the form of backpressure.. turbos require pressure in the exhaust manifold in order to spin and do work. that pressure pushes against the piston on its exhaust stroke and "restricts" the engine. the plus side is you are cramming a whole bunch more air in the intake side so it is a net gain. but it is not "free" power. and yes, when turbo is off boost you have a nice restriction in your exhaust. however, it's likely the restriction is less loading on the engine than a mechanical supercharger.

i think a blown engine would need just as low compression for a certain boost level, would it not?

That depends how much boost it is running and the type of fuel it uses. The temperatures of induction produced by superchargers are typically lower than their turbocharger counterparts, so you can get away with higher compression and no intercooler. That said, yes - from factory, supercharged engines usually do come with low compression. But keep in mind that the supercharger (atleast a roots type) is producing boost from idle onwards so you don't really feel the effects of running low compression. Therefore no feeling of lag and boost (they technically lag for the whole rev range, you just don't notice this because there isn't a big non-linear change of torque like with a turbocharger). The supercharged V6 Commodores of the 90's were as fast as their V8 counterparts off the line, due to similar low down torque, but lost out above 80km/h.

But keep in mind that the supercharger (atleast a roots type) is producing boost from idle onwards so you don't really feel the effects of running low compression.

That's the big benefit - they feel like a bigger engine without the weight penalty.

doesn't seem to be any bolt on supercharger kits for the supra/skylines, especially for the NA boys, could be a route with less headaches, although not necessarily costing less.

NA-S?

That said, if there was a supercharger kit for the NA supra, i might even consider getting another supra, as a fun daily.

if only.

Edited by xALmoN

Would be such a waste when there is already a forced induction model of that car available for cheaper.

The only cars I would ever aftermarket turbocharge/supercharge are cars that never came with it from factory. It almost ALWAYS ends up costing more than the factory version. Tthe only exception I can think of is a VL turbo because those factory cars holding their value in a way that defies the laws of depreciation.

you can't make the same power. theres a point where the supercharger has peaked the turbo will keep going.

they won't fit in a lot of engine bays.

Twin charging is awesome if you can be bothered tuning with many hiccups.

the only advantage is in an engine such as an ls1. where turbo chargers melt the damned thing.

torque sucks you hit your peak then get overtaken.

it's only for initial take off.

I'd like to hear from someone who went from turbo to supercharger on the same engine.

If you're setting up a car for street acceleration, roots superchargers are pretty good...by the time you run out of torque you've already passed the speed limit on most roads.

Bottom line, they both have advantages/disadvantages...but OP was referring to motorsport. In which case, track based motorsport tends to favour the turbocharger and drag racing favours the supercharger. Not because one is necessarily better than the other, but because one is generally better suited to that application.

if you really want an argument stop calling it lag and start talking about boost threshold

this is like the 2nd time i've seen someone on here who actually made note of the difference, good work

face palm at how some people dont realise how closely horse power and torque are related .

now i'm really starting to like you :)

^^ agree, in the sense that turbos don't give you "free energy" by harvesting exhaust gases. you do have a penalty and that penalty is in the form of backpressure.. turbos require pressure in the exhaust manifold in order to spin and do work. that pressure pushes against the piston on its exhaust stroke and "restricts" the engine.

its more commonly reffered to as 'pumping losses' and turbos still have the same issue, those its less noticeable then with a supercharger

i think a blown engine would need just as low compression for a certain boost level, would it not?

not necesarily. superchargers have one big advantage of being able to run large diamter extractors to an open exhaust , as opposed to a turbo manifold+turbo combo, extractors and open pipes get more heat out of the cylender easier (thats the theory anyway lol)

On the topic of supercharger versus turbocharger efficiency, there is some misleading information here...remember that off boost a turbocharger is very restrictive to engine breathing and the engine is operating at low compression (therefore wasting combustion) for 1/3 of the rev range, where we spend most of our time driving. The only time they can be considered efficient is when they are on boost. And even then, they are considered thermodynamically inefficient despite producing lots of power. So a supercharger isn't the only one that is wasting/draining energy on the constant, and the exhaust side of things is never restricted. In fact, in the lower rev ranges it is more efficient than a turbocharger.

You need to think of the comparison as linear versus non linear power production. Both have their advantages and disadvantages.

but overall, turbo is more efficient.

vast majority of the worlds trucking fleets run, turbo diesels. there's now even more small cars with turbo diesels for that extra efficiency.

Edited by Peter89

bmw has said for years that turbochargers are the way of the future. for all applications where the extra force required to pump the air through the turbine is less than what is required for the supercharger, the turbo will be more efficient at generating power (fuel wise at least).

the mercedes mclaren slr needs 120 hp to power its supercharger!!! thats more than my lil bros camry makes hahaha

on the racing front, remember the most powerful f1 engines ever were the 1.5L turbo ones, producing 1500hp!!! pretty epic huh

also a supercharger can only spin at 1/3 the speed a turbo can.

they should be rebuilt every 100k whether damaged or not. cost more, yet less complicated too install. if there's room.

can drain upto 20% of the engines overall power to run.

yet add around 30-75% say 50% for most.

http://www.ehow.com/facts_5752326_turbo-vs...onsumption.html

I honestly don't like the whine of large ones often hear it over a noisy v8.

roots last longer yet aren't as efficient as a twin screw.

centrifugal is great on a standard car if you want low boost.

for some reason i want to put one on a n/a 4 cylinder.

but overall, turbo is more efficient.

vast majority of the worlds trucking fleets run, turbo diesels. there's now even more small cars with turbo diesels for that extra efficiency.

That's cause turbos work better with diesels. They don't rev high (as per a longer stroke than petrol engines) and this would severely limited boost in a supercharger application. Turbo lag is also much less noticeable on a turbo diesel because they are high compression engines - in fact, the turbocharger is solely there to extend the useable range of the diesel engine in the middle and upper RPM (they run out of steam very quickly), rather than to produce more torque/power all round.

It's all about application. There's no "one is better than the other". One will always be better for your application than the other..."which one" depends on your application. Vehicle manufacturers around the world still have a divide about it, there's no general consensus that one is better than the other, which is why twin charging exists.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...