Jump to content
SAU Community

Recommended Posts

ive heard about people using a magical combination of nissan turbo housings and a specific cartridge to create this supernatural fabled turbo lol

i would like to know which ones ???

what size front inducer and exducer and what size rear

also any info on housing diameters and what is printed on them ie op6...mm? 45v1/2/3/4 ...mm? etc

and best combinations of said parts

but not limited to rbs any info atall would be great just wanna learn as much as possible as this really interests me

thanks guys

Mythical turbo? Supernatural fabled turbo?

I am not sure if you were drinking or smoking something last night but I bet your post made lots of sense when you typed it.

Seriously, WTF?

Turbos are air pumps.

What car, what engine, what use (daily/track/strip), what power level do you want?

Answer these questions and give the forum something to work with.

Standard nissan housings are used for convenience to allow the turbo to remain stock looking and are machined out with larger turbine and compressor wheels fitted. Hi-flowed turbos generally seem to struggle when larger than 450hp cores are fitted but there are hybrid housing from new castings or with compressor housing changes are making more power with a cost of downlow response.

There is lots of information on these topics from hypergears turbo thread somewhere just below this post through to wealth of posts over the last 7 years or so on what works and what doesn't.

lol

if you wanna learn, read through threads like the hypergear hi-flow thread here.

getting the right size turbo, you have to take many things into account:

engine size

target power

how the car is being used. ie. drift, street, drag etc

and many more

use the search function, as no doubt its been covered before

There are better threads to read than that one...unless he's after a mythical combo then perhaps he can read that thread...

Read page 39 of that tread. There is a mythical turbo there turns your RB25 into a V8. lol

Edited by kwickr33
ive heard about people using a magical combination of nissan turbo housings and a specific cartridge to create this supernatural fabled turbo lol

Aaron from Sliding Performance used to rebuild turbz that worked quite well on RB25s using machined VG30 housings and Biaggio CHRAs, until it became nearly impossible to find cheap VG30 comp/turbine housings

As ppl have said, the Hypergear rebuild using machined O.E RB25T housings and their specific CHRA seems to be the go on a budget these days

hahaha i was just trying to get your attention, worked though hey, mythical....bahaha

im looking for info on the housings and cartridges inducer and exducer mesurements that is all

ive heard of people using different combinations to acheive quite a nice power figure around the 240kw mark with great response

i hear the 45v4 front and op6 rear is the largest is this true? what are the the mesurements and what cartridge has the largest steel front and rear wheels

Step 1, Initialize SAU

Step 2, Forums

Step 3, Forced induction

Step 4, Quick Ref Guide

Step 5, $350 Turbo - 250rwkw (RB25DET)

Step 6, Dont waste your time.

http://www.skylinesaustralia.com/forums/35...-9b-t22706.html

Good read, exactly the thread you are looking for. Has links to other relevant threads too I believe.

You will need access to a turbo re builder willing to do the work for cheap. Housings will need to be machined, odd parts will need to be sourced, specific instructions given to builders etc. Last time I approached GCG with the exact specs they laughed at me, primarily due to the fact they were not confident enough they could do it. They did however urge me to have them high flow the turbo for me at a cost of roughly $2000.

Now if you want to be realistic you can spend about half that having hypergear do you a high flow. I am sure he will also use whatever mickey mouse wheels you ask him to.

If your serious about it, find the turbo that suits your expectations as per the dyno thread and never look back.

http://www.skylinesaustralia.com/forums/Rb...yno-t55845.html

hahaha i was just trying to get your attention, worked though hey, mythical....bahaha

Nah, were you pissed or stoned weren't ya.

Why you would want to make your own mongrel when the turbo shops have done the work with their own hi-flows or you can buy an off the shelf item from Garrett or Hks beats me.

240rwkw is firmly in GCG hi-flow range, HKS GT-RS in ball bearing or Hypergear can sort out one of his bushbearing turbos and you can benefit from their R&D.

Problem solved.

240rwkw is firmly in GCG hi-flow range, HKS GT-RS in ball bearing or Hypergear can sort out one of his bushbearing turbos and you can benefit from their R&D.

Not to mention hypergear have had some very impressive results of late!

As stated, go with the results that have the R&D to back.

Step 1, Initialize SAU

Step 2, Forums

Step 3, Forced induction

Step 4, Quick Ref Guide

Step 5, $350 Turbo - 250rwkw (RB25DET)

Step 6, Dont waste your time.

http://www.skylinesaustralia.com/forums/35...-9b-t22706.html

Good read, exactly the thread you are looking for. Has links to other relevant threads too I believe.

You will need access to a turbo re builder willing to do the work for cheap. Housings will need to be machined, odd parts will need to be sourced, specific instructions given to builders etc. Last time I approached GCG with the exact specs they laughed at me, primarily due to the fact they were not confident enough they could do it. They did however urge me to have them high flow the turbo for me at a cost of roughly $2000.

Now if you want to be realistic you can spend about half that having hypergear do you a high flow. I am sure he will also use whatever mickey mouse wheels you ask him to.

If your serious about it, find the turbo that suits your expectations as per the dyno thread and never look back.

http://www.skylinesaustralia.com/forums/Rb...yno-t55845.html

thanks mate ...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
    • Ah coolant overflow, previous discussions make way more sense now lol. 
×
×
  • Create New...