Jump to content
SAU Community

Recommended Posts

hi guys i bought my 94 r33 rb20de 3 days ago and realized under heavy braking that my oil light comes on and i my pressure gauge drops to 0 i have no idea if this is the normal or not but if anyone could enlighten me or give me a few things to check out that would be a great help and i would appreciate it immensely cheers jamie

  • Nope 1
Link to comment
https://www.sau.com.au/forums/topic/336474-oil-pressure-when-braking/
Share on other sites

Is it really a n/a rb20 in a 33? i find that hard to believe unless someone corrects me?

if so you have close to the worst combination of car and motor, the only thing worse you could have is the single cam rb20e.

+1 as said, check your oil. Did the car have an inspection before you bought it? is the oil pump going ok? has the motor been replaced with an rb20 for some reason?

Ive heard of RB20DE R33's but yeah the RB25 is favoured over the 20 for obvious reasons

OP: Check your oil level, if thats fine I'd say its a dodgy bit of wiring to your oil pressure sender or your oil pressure sender itself might be broken

I don't think R33 came in RB20DE - They came out in RB20E, RB25DE, RB25DEt, RB26DETT (GTR)

You might have a SOHC RB20. :P

Might be worth checking oil level.

I recommend new oil and filter.

Actually I think you are right, only the RB20E was available...even gayer lol. I swear I remember reading they were not approved to bring into the country but some still got in.

Personal import maybe....

The oil light is of the "Oh SHIT!!!!" type. If it comes on, then you have no oil pressure, and that is NOT good for the engine..

One way to avoid it is to not brake so heavily that it comes on. One other method is to change the oil.

  • 1 month later...

check the sump is not damaged, if its been punched up it may have damaged the pick up tube higher up, causing it to pull air on braking, even when your oil level is correct. can test this by overfilling oil by a litre. sr20s common for it.

  • 2 weeks later...

You could get a skyline with a CA18i in Japan, yes thats right, a 1.8 litre SINGLE CAM.

No idea why anyone would get it, but I have seen photo evidence of such a beast.

Regarding the oil problem all you can really do is overfill the engine slightly, I believe that the higher and softer the suspension the worse it is as well (more weight shift).

edit: The car is a R32 GXi and it makes 68kw at the fly, f**king woeful.

edit2: Its not even proper injection, its single point tb injection ahaha

Edited by Rolls
  • 1 month later...

I've seen this once when braking hard, thankfully I had already put the clutch in and the revs had dropped to about 1500rpm when the oil light flickered on. My oil level was about midway between L and H on the dipstick.

FWIW I always put 5L of oil in when I do the change, preferably the oil is slightly above the H mark. There's a kink in the dipstick and I figure that's the "knob end" warning mark that you'll end up crank slapping the oil if you fill it past that, mine is always just below that point.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...