Jump to content
SAU Community

Recommended Posts

An R34 GTT was quoted from factory at 206rwkw, a standard one on the dyno usually got around the 160 mark but it varies according to tyres, different diffs, gearboxes [manual vs tiptronic], even the oil and bearings used.

You can 'safely' say that you will lose at least 30rwkw as a baseline for a skyline. Then it depends on how much power your car makes as to the overall loss.

As a hypothetical example = A 600kw car will be more efficient but still lose more in total than a 100kw car because the harder you work something the higher your friction component. So it might lose 60rwkw but still make 540 and the 100kw car might lose 20rwkw and make 80, as a percentage of total power the 600kw car is then more efficient, 90% vs 80%. It loses more because it is revving harder, and working more thus increasing losses overall to friction.

But it all gets way too hard to actually calculate a result with any certainty, too many variables - so as TiTan said the dyno is the best solution.

An R34 GTT was quoted from factory at 206rwkw, a standard one on the dyno usually got around the 160 mark but it varies according to tyres, different diffs, gearboxes [manual vs tiptronic], even the oil and bearings used.

You can 'safely' say that you will lose at least 30rwkw as a baseline for a skyline. Then it depends on how much power your car makes as to the overall loss.

As a hypothetical example = A 600kw car will be more efficient but still lose more in total than a 100kw car because the harder you work something the higher your friction component. So it might lose 60rwkw but still make 540 and the 100kw car might lose 20rwkw and make 80, as a percentage of total power the 600kw car is then more efficient, 90% vs 80%. It loses more because it is revving harder, and working more thus increasing losses overall to friction.

But it all gets way too hard to actually calculate a result with any certainty, too many variables - so as TiTan said the dyno is the best solution.

Why will it be more efficient?

I would have thought the more power you're producing at the fly, the more you're going to lose through the transmission and diff, in terms of efficiency as a percentage?

I was always told you lose 25% between flywheel and the rubber, but that said hypergear's done a lot of this stuff. Isn't there a way of measuring the power at the fly by determining the friction/resistance/losses through the box and diff? I swear I read about James May explaining it once...

Edited by Galois

The losses are not a percentage but a number e.g. 25kw for auto 25kw for awd etc. People who think they are making say 30% more at the fly than they are getting at the wheels are most likely being wildly optomistic at higher power levels. In any case the only really useful figure is the one you are making at the wheels v the last figure you were making at the wheels on the same dyno.

It'd be some kind of multi-variable equation.

Easiest guess is a percentage say 20% more at the treads.

A better model is a flat number of say 25rwkw plus a percentage of ~10%

The best model would be some multi-variable non-linear equation.

An R34 GTT was quoted from factory at 206rwkw, a standard one on the dyno usually got around the 160 mark but it varies according to tyres, different diffs, gearboxes [manual vs tiptronic], even the oil and bearings used.

You can 'safely' say that you will lose at least 30rwkw as a baseline for a skyline. Then it depends on how much power your car makes as to the overall loss.

As a hypothetical example = A 600kw car will be more efficient but still lose more in total than a 100kw car because the harder you work something the higher your friction component. So it might lose 60rwkw but still make 540 and the 100kw car might lose 20rwkw and make 80, as a percentage of total power the 600kw car is then more efficient, 90% vs 80%. It loses more because it is revving harder, and working more thus increasing losses overall to friction.

But it all gets way too hard to actually calculate a result with any certainty, too many variables - so as TiTan said the dyno is the best solution.

Whoa there! factory outputs are always at the flywheel, no as quoted in bold.

Eg a 32GTR is quoted as 206KW (more like 220KW), and stockers put out on average 170RWKW.

driveline loss in any rwd car on average is usually around 20-25% isnt it?

For eg..500hp engine puts about 300kw(400hp) at the wheels..

works out to 20%

Edited by Arthur T3

It's not 20% - this argument has been had time and time again on these pages.

It seems to be around a "fixed" ~60rwkw amount from all discussions.

It's certainly not 20%. Think about it, 800hp motor is losing 160hp (120kw)? Nope.

If you fix it @ 60kw... GTR's around 220-230kw factory (even though its quoted @ 206, we all know its not).

And most stock GTR's make around 165-180rwkw on a dyno so it certainly fits quite nicely.

Until it's actually tested, which to date no body has, then it's impossible to say overall anyway.

That said - I will investigate with Nizpro & Racepace the feasibility of doing this testing in the next couple of months for everyone along with some other general forum speculation stuff i wanna cover :whistling:

Whoa there! factory outputs are always at the flywheel, no as quoted in bold.

Eg a 32GTR is quoted as 206KW (more like 220KW), and stockers put out on average 170RWKW.

yeah, good call, my mistake, I meant flywheel kw and if you read it as that the sentence makes sense.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...