Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

If only I could get in contact with UniGroup when need be they'd have some business from me too. Are their any days/hours where UniGroup are definitetly open or definitely by the phone?

Of the 5 different dyno's (days) i've been too they have by far the best service/knowledge.

  • 1 year later...
When I'm not doing it, my car is tuned exclusively by Unigroup Engineering.

www.unigroup.com.au

Yavuz and Valent are very communicative guys and have tuned some very very fast and big dollar cars that are still running hard.

I cannot speak highly enough of their efforts in correcting my tune on the pfc.  Less ignition advance, more fuel, same power.  They are also happy to tell you exactly what they're doing as they do it which helps you stay in the loop.

I must have picked their brains 20 times since first going there, (phone, email etc) and have found them more than happy to chat.

Yavuz also operates one of the dynos for Dyno Dynamics at Summernats.  Expert with the Power FC and how it should be tuned for our cars and your application.

Adrian

agreed

getting my pfc tuned next week there

sounds like Ben is a good name for a tuner lol...

drop Ben from BEL Garage a message, www.belgarage.com.au

road tune for part throttle mapping + response, dyno to clean up top end, won't let anyone else tune my car :P

ive been there once to buy an air filter off them. they seem like nice guys.

also, Haak are good too. they're on the horsley drive right near eastern creek. Dave there is really good...

Spoken to alot of the customers that were waiting at CRD whilst waiting for my tune to finish and many of them were ex-customers of the above mentioned tuners....Ummm I wonder why that is?? AnywayI ask them why they didn't come to CRD and see Jim in the first place and the standard response is:

"Yeah I should've, but the other guys were cheaper.."

Very wise aren't you?? Now you guys have to pay again...

A small tip: Do it the right the first time...You get what you pay for.

Edited by Demon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...