Jump to content
SAU Community

Recommended Posts

So basically I was going from a 60 to a 100 zone, car started reving up and making boost and the engine cut out, died completely.

Fortunately there wasnt much in the way of traffic and I had a mates following me in another car (we were going to go camping). The car struggled to turn over, but got there after a couple of attempts but sounded a bit spluttery and the engine light was on. Managed to limp it back home, but I it wont rev much past 2000 rpm, if I tried it would bounce the revs back and forth over a 100-200rpm range and surge almost like a bunny hop. We pulled in to a servo part way back, my mate was low on fuel. I didnt need to fill up but when I went to restart it it REALLY struggled to get going again, almost thought it wouldnt start up at all.

Ive tried to pull the ECU codes, got four zeros. Took the front end off to check the intercooler piping, and also checked the engine bay - all looks to be fine (Im not a mechanic by any stretch though)

Anyone got any thoughts or suggestions as to what I can do/check to isolate the problem?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/338999-limped-my-m35-home/
Share on other sites

Airflow meter?

That thought crossed my mind too, but surely thatd through an ECU code? http://www.skylinesaustralia.com/forums/Ob...st-t281894.html indicates there are AFM malfunction codes.

Hope you get it sorted quickly.

Cheers mate

Sounds like airflow meter Dunc, at least they have been sourced cheap now, around $80 or so new I think. I have no idea why the codes didnt come up...

Can you borrow somebody's to try?

Its possible to check an AFM with a multimeter, isnt it? Maybe I should give that a go

I take it there arent any AFMs that would work other than a unit off another M35?

Its possible to check an AFM with a multimeter, isnt it? Maybe I should give that a go

I take it there arent any AFMs that would work other than a unit off another M35?

Quite a few cars use the same airflow sensor but in a different housing, Subaru use it, and many VQ's like maxima.

i let scotty operate on mine too - and they arent repairable as per the older ones.

so will be a new/second hand one

they are available on yahoo auctions japan.

and before you try a 350Z one wont work as the adaptors are different.

unsure about the skyline v35 350gt but id imagine they are the same as the 350Z

mine did the exact thing about 4 months ago.

i was overtaking a car and was in boost when it died mid flight!!!

it was the air flow meter.

I remembered bits and pieces of your thread - couldnt remember the outcome or exactly what was the go. Its reassuring to hear that someone had the same problem and the fix wasnt too costly.

Time to get in contact with Jesse Streeter I guess, doubtful I'll be able to source one here for cheaper than what I can do on Yahoo auctions!

I remembered bits and pieces of your thread - couldnt remember the outcome or exactly what was the go. Its reassuring to hear that someone had the same problem and the fix wasnt too costly.

Time to get in contact with Jesse Streeter I guess, doubtful I'll be able to source one here for cheaper than what I can do on Yahoo auctions!

They are available here, im sure Jetwreck got onto a cheap source...

Airflow meter? Hope you get it sorted quickly.

+1 and +1

AFM Nissan part number is 22680-6N211

It should be the same as used in the 2001-2007 X-trail and the 2000-2005 Pulsar

Or you could pick one up on Yahoo... they are routinely on there for under $30 (ex shipping & commission)

Edited by iamhe77
  • 2 weeks later...
Quite a few cars use the same airflow sensor but in a different housing, Subaru use it, and many VQ's like maxima.

you serious ?

doubt my 98rexy spare afm would suit surely ?

Edited by PetroDola

mate i had the same issues about two weeks ago, i only just managed to get my car home, i took out the air flow meter and sprayed it with contact cleaner and it worked an absolute charm, the car hasn't gone better, it's always worth a shot.

So basically I was going from a 60 to a 100 zone, car started reving up and making boost and the engine cut out, died completely.

Fortunately there wasnt much in the way of traffic and I had a mates following me in another car (we were going to go camping). The car struggled to turn over, but got there after a couple of attempts but sounded a bit spluttery and the engine light was on. Managed to limp it back home, but I it wont rev much past 2000 rpm, if I tried it would bounce the revs back and forth over a 100-200rpm range and surge almost like a bunny hop. We pulled in to a servo part way back, my mate was low on fuel. I didnt need to fill up but when I went to restart it it REALLY struggled to get going again, almost thought it wouldnt start up at all.

Ive tried to pull the ECU codes, got four zeros. Took the front end off to check the intercooler piping, and also checked the engine bay - all looks to be fine (Im not a mechanic by any stretch though)

Anyone got any thoughts or suggestions as to what I can do/check to isolate the problem?

Cheers!

Have you run over anything? like a rock that could possibly squash your fuel lines?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...