Jump to content
SAU Community

Recommended Posts

Thanks for the heads up guys, I went down to Supergas for a winge today and ended up speaking to the sales manager on the phone while at the counter. He ended up giving me a 10.5m3 refill for $125, less than half what I was paying.

I don't have pics of the damaged manifolds, one I had to repair, and one I saw on a car, the crack was definitely down in the webbing but it could have started beside the weld and cracked further away as it made it's way around the pipe. I didn't get a good look at it as it was on the car. It was probably 2mm tube so very thin and light stainless. It would glow white hot on the dyno within a second or two of hitting boost. My point was, he had a GT42 mounted without a hanger or support, and a 4 inch exhaust with no hangers till the diff. Perhaps it would have lasted longer if the manifold could move around on the head a little and the turbo was supported.

Still need to make a inlet for the bov

Let me know what you guys think !

Looks good Angelo, just face the BOV return towards the compressor, cut on a 45 degree angle, and weld it in. It will take a while to die grind the hole, partly the reason I use alloy for my intakes as it's much easier to shape the holes in.

Good news on the gas mate! What kunce though slugging ya that much a bottle especially when it looks like your a regular customer who does a fair bit of welding ;)

Im doing some pipework on my dads GTR tomorrow so hopefully I can get some pics up afterwards :)

Thanks for the heads up guys, I went down to Supergas for a winge today and ended up speaking to the sales manager on the phone while at the counter. He ended up giving me a 10.5m3 refill for $125, less than half what I was paying.

I don't have pics of the damaged manifolds, one I had to repair, and one I saw on a car, the crack was definitely down in the webbing but it could have started beside the weld and cracked further away as it made it's way around the pipe. I didn't get a good look at it as it was on the car. It was probably 2mm tube so very thin and light stainless. It would glow white hot on the dyno within a second or two of hitting boost. My point was, he had a GT42 mounted without a hanger or support, and a 4 inch exhaust with no hangers till the diff. Perhaps it would have lasted longer if the manifold could move around on the head a little and the turbo was supported.

I have a couple of vices, and a set of small vice grip pointy pliers. None are big enough for 4 inch unfortunately, I need to find a larger vice or find another way to hold larger tube.

I am making this 4 inch intake atm, for a GTX35 in a 33. The VQ afm should be good for over 450wkw resolution in 4 inch tube by my calculations. To be tuned with a PFC. :)

post-63525-0-42753000-1379429933_thumb.jpg

post-63525-0-89247800-1379429990_thumb.jpg

The reason thin walled china manifolds crack is due to expansion, they would crack just as easily if purged imo. If the manifold flange is split and the turbo/exhaust weight is carried by a well designed bracket of some sort, the manifolds would probably last for years (on road cars at least.)

I only purge exhaust pipes when the die grinder can't get to the back of the weld, this isn't food grade exhaust I am working on, and at $300 a bottle of argon I'm not going to waste it back purging unless I need to. I have never had any dump pipes or exhaust returned from weld failure either, track cars included.

One thing i can say, I definitely prefer to weld thin wall (1mm or thinner) while back purging as I am much less likely to blow holes and can crank much more current in. No doubt it is stronger, but this isn't a structural item we are talking about. Perhaps you get better pricing on Argon through your work Mick?

My 2c ... chinese manifolds crack not due to absence of support or purging...its purely down to the fact that there isnt any penetration. I have only looked at 3-4 China manifolds but none of them had any penetration. Even my old Greddy manifold only had intermittent penetration. Purging of course helps ontrol peno without cauliflower so is related.

Looks excellent! However, couldn't you have rotated the housing to avoid having that elbow?

Looks excellent! However, couldn't you have rotated the housing to avoid having that elbow?

Thanks. There was a reason i did it like that an I can't remember why haha, possibly due tithe size of the housing and manifold position it may have hit ac lines and compressor or pwr steering lines not sure it was a while ago. It was just easier to do that, plenty of big turbos are positioned the same. And since I was doing it in lobster back why not show off the stainless work. Edited by r32gtrs

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...