Jump to content
SAU Community

Recommended Posts

Someone is paying attention!

Ok, how about WRC cars...

Well

the antilag setup works almost like a blow off valve

dumps pressure from the intake into the exhaust manifold

They were also rebuilding the whole car and replacing turbos after every event

  • Like 2

Alex, everyone has differing opinions and theories, and sometimes mine are well out of the box, but I also prove mine on many occasions by making it work and getting the results. My theories have yet to let me down in practice, and I help build quite a few high power cars for customers. No-one is wrong in any situation, and if your 'Bolt-on' approach is easier by all means go for it. Remember, there is always a better way though.

This bloke! :)

The whole point of the turbo speed sensor is so you can make sure where on the compressor map you are. Going outside of that compressor map is for people that have dyno queens, or run some sort of ice box for drags, as it superheats the air, reduces effency and increases chance of engine damage.

Borg Warner broke the existing turbocharger mold when it created the EFR line. One of the main goals was integrating other turbo system components into the turbocharger. This ploy can save time, money and headaches. The biggest integration is the inclusion of an integrated blow-off valve. No more bung welding on delicate intake pipes. The BOV is laid-out as a compressor recirculation device that redirects the charge air from the turbo's compressor outlet to a low-pressure point just before the compressor inlet, which really helps keep the unit spooled between shifts.

I think you mean innovation.

They haven't done anything amazing they have just allowed Joe Average buy a turbo with all the fancy stuff for a cheap price (in comparison to a real motorsport turbo that retail around $10k).

You keep reading of the catalogue you need to think about what the actual turbocharger is doing and what is happening to the air.

-sigh-

If you guys on actually care for all the technology offered in this package.. why bother for such an expensive turbo with barely any results... Why not just got for a proven Precision, which happen to make the light switch power your interested in, all for a low cost... AND no real mounting issues....

The whole point of the turbo speed sensor is so you can make sure where on the compressor map you are. Going outside of that compressor map is for people that have dyno queens, or run some sort of ice box for drags, as it superheats the air, reduces effency and increases chance of engine damage.

Oh crap, FP don't have compressor maps... Whatever would you do in that case?

The sky is falling... :P

Why not just got for a proven Precision, which happen to make the light switch power your interested in, all for a low cost... AND no real mounting issues....

Just ceramic bearing failures. :/

Been there tried that...

Oh crap, FP don't have compressor maps... Whatever would you do in that case?

The sky is falling... :P

FP make good street turbos, and the best 'bolt-on' solution for a number of make and models.

But personally, I just don't know where mine is (on compressor map), which is why I run it on such low power on track. I just want consistent power. I think FP make great compressors, but it frustrates me they done provide compressor maps. Oh not to mention that it annoys me about the turbine side and dump pipe design...

You can hardly call FP in the same league as EFR, ESPECIALLY in motorsport applications.

I run Garrett and recommend them whenever possible.

What I am after is a cheaper EFR without the bling. I only want the turbine/shaft preferably, shoved into a Garrett GTX core.

If Garrett release a Ti wheel, BW will have missed their chance of a lifetime. No skin off my nose.

FP make good street turbos, and the best 'bolt-on' solution for a number of make and models.

But personally, I just don't know where mine is (on compressor map), which is why I run it on such low power on track. I just want consistent power. I think FP make great compressors, but it frustrates me they done provide compressor maps. Oh not to mention that it annoys me about the turbine side and dump pipe design...

You can hardly call FP in the same league as EFR, ESPECIALLY in motorsport applications.

Why do you need a comp map....wouldn't a IAT/EGT sensor combo and a tune pushed to the limits of diminishing returns be enough to tell you if you are in its "efficiency zone"...?

Why do you need a comp map....wouldn't a IAT/EGT sensor combo and a tune pushed to the limits of diminishing returns be enough to tell you if you are in its "efficiency zone"...?

Correct, and be much more accurate than a made up map to suit a made up application.

Every engine will behave differently, depending on what you have in the way of restrictions to flow. After all, boost is only a measure of restriction.

You can hardly call FP in the same league as EFR, ESPECIALLY in motorsport applications.

NONE of the alternatives mentioned are in that league though - so that doesn't really say too much. FP don't release compressor maps but there is enough info out there to get a reasonable idea of what the different compressors flow like where, definitely enough to get an idea of where each sit in the scheme of things, lack of compressor maps don't hurt Precision and to be fair I suspect 90% of people here don't really pay attention to comp maps or other related info and dynamics when choosing turbos.

FP have some epic turbos, Garrett also suffer the same lack of twin scroll housing etc stuff you are complaining about - funnily enough most of the same housing options are available to both. The FP Black is a pretty awesome turbo, have you actually had it running and tuned yet?

  • Like 1

The FP Black is a pretty awesome turbo, have you actually had it running and tuned yet?

Yes it is an awesome turbo. I haven't run it on my new setup, only my old 2.3L. We didn't run it too hard, only 23psi in which it made a very lazy 300kW on e85.

Spool was really good for a turbo its size, but transient response wasn't the best... Journal bearing turbo..

I run Garrett and recommend them whenever possible.

What I am after is a cheaper EFR without the bling. I only want the turbine/shaft preferably, shoved into a Garrett GTX core.

If Garrett release a Ti wheel, BW will have missed their chance of a lifetime. No skin off my nose.

I am inclinded to agree. If I had my choice again I would have gone Garrett, but at the time they didn't have the range in the GTX series or the range of housings.

Yes it is an awesome turbo. I haven't run it on my new setup, only my old 2.3L. We didn't run it too hard, only 23psi in which it made a very lazy 300kW on e85.

Spool was really good for a turbo its size, but transient response wasn't the best... Journal bearing turbo..

Oh you have the non-DBB one - for some reason I thought it was the DBB version. I've only experienced the 82HTA compressor in a twin scroll GT3582R HTA setup and that was really really impressive response for the power it was making, "only" a pump gas setup too making around 500whp (DD rolling road style) on a 2litre. GTX I feel is more miss than hit given how far behind Precision and FP they were in releasing their technology, most the FP wheels offer better flow versus response - though now they've raised their prices (when GTX came out the HTA were cheaper) there seemed pretty much no point bothering with the GTX range, though now if you want an HTA with a non-plastic bearing cage it's pretty expensive.

For RBs the EFRs are easily the best, they aren't particularly hard to fit big singles - not a lot more expensive considering the performance, and strong as anything... I find it weird that people have issues with the extra bits, they perform and save other bits of expense... especially if you are building a new setup. Not having to fabricate a place to fit a BOV, and buying the BOV in the first place definitely will save some coin and space and I don't mind the look of them, I reckon they look pretty serious business as opposed to yet another Garrett/Honeywell stamped compressor cover that could be anything from a T3/T4S up to a GTX3582R.

  • Like 1
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
    • Not yet quite as bad as what we've seen a Jim Berry clutch do in an R32 GTR though when it decided to cut a chassis rail in half... Still very very gnarly and a great reason to avoid.
×
×
  • Create New...