Jump to content
SAU Community

Recommended Posts

Picked up my car this morning, resplendent in new heatwrapped mid pipe, 100 cell hiflow cat, and shiny Fujitsubo exhaust fitted. Now it's 3" from turbo to tip.

Canak Autosport did a beautiful job on the mid pipe; tucked up nice and close to the floor, out of harms way. Cost a little more than I expected, but there's almost $400 in cat, flex joint and flanges.

Sounds brilliant, no drone, just a sweet rumble at idle, and nice rasp as you rev out. Now pushes almost 15 psi instead of 12, feels so much more responsive!

One very happy camper.

Picked up my car this morning, resplendent in new heatwrapped mid pipe, 100 cell hiflow cat, and shiny Fujitsubo exhaust fitted. Now it's 3" from turbo to tip.

Canak Autosport did a beautiful job on the mid pipe; tucked up nice and close to the floor, out of harms way. Cost a little more than I expected, but there's almost $400 in cat, flex joint and flanges.

Sounds brilliant, no drone, just a sweet rumble at idle, and nice rasp as you rev out. Now pushes almost 15 psi instead of 12, feels so much more responsive!

One very happy camper.

Good stuff Dale...

Picked up some 33gtr swaybars last night, will chuck them in on the weekend and pull the diff out to be dropped to my diff guy on Tuesday... SkidWagon is getting close.. BRING ON POWERCRUISE!

Picked up my car this morning, resplendent in new heatwrapped mid pipe, 100 cell hiflow cat, and shiny Fujitsubo exhaust fitted. Now it's 3" from turbo to tip.

Canak Autosport did a beautiful job on the mid pipe; tucked up nice and close to the floor, out of harms way. Cost a little more than I expected, but there's almost $400 in cat, flex joint and flanges.

Sounds brilliant, no drone, just a sweet rumble at idle, and nice rasp as you rev out. Now pushes almost 15 psi instead of 12, feels so much more responsive!

One very happy camper.

Bet that sounds shit hot also Daleo..as well as looking quite smart! *thumbs up* :O

Im actually wondering if the HKS suited for the M35 sports muffler on my full 3" system from scotty actually gives more power than the fujtsubo / kakimoto M35 systems. I know the Fujitsubo and Kakimoto's have a much nicer quieter tone. (bit like a rexy bob)

My question is would there be any difference as mine is like 50 times louder?

Edited by PetroDola

I think it comes down to the design more so than how loud it is.

Both the Fujitsubo and Kakimoto exhausts are designed to flow as much air with as little restriction as possible while their muffler setups use vastly different designs to control the sound/volume

I think that the only way to tell if yours makes more power would be to dyno them back to back on the same car.

You can't look at Scott's dyno results for a comparison between the two because he changes shit on his car every second day :O

Edited by iamhe77
I think it comes down to the design more so than how loud it is.

Both the Fujitsubo and Kakimoto exhausts are designed to flow as much air with as little restriction as possible while their muffler setups use vastly different designs to control the sound/volume

I think that the only way to tell if yours makes more power would be to dyno them back to back on the same car.

You can't look at Scott's dyno results for a comparison between the two because he changes shit on his car every second day :O

hrmm good Point Iain.

Im wondering if scott has any dyno's done with just that exhaust mod from stock :huh:

and what impact it had...would be interesting to know the difference for sure.

Cheers!

Had the 260RS profesionally detailed today. Got the lot done for $300 which I recon is bloody cheap! Then brought it home and polished the GReddy intake pipes. Man I love this car even more now!! :)

A bit lame but bought some 15mm hubcentric spacers from JustJap.

Matt@JustJap had them delivered to my door within 3.5hrs (ordered 10.15am sitting on the doorstep at work by 1.45pm). That is outstanding service and deserves a pat on the back.

I have a HKS2835ProS going on next week to replace the perfectly fine HKS GT-RS which will be a more interesting mod. More on this next week.

hrmm good Point Iain.

Im wondering if scott has any dyno's done with just that exhaust mod from stock :D

and what impact it had...would be interesting to know the difference for sure.

Cheers!

I asked for the system to be fitted when I bought the car so no pre graphs, I cant even remember what it drove like... I think the words were "4 cats, you are kidding right". :blink:

hrmm good Point Iain.

Im wondering if scott has any dyno's done with just that exhaust mod from stock :D

and what impact it had...would be interesting to know the difference for sure.

Cheers!

Im pretty sure you replied to Cam's post and not mine mate :P

its not like we are remotely the same, he has a gay coloured car!!

lol... and you have a stock kinda car (or is that a "gonna" kind of car :laugh:) with an old-man interior!

Anyway, minor-ish service on my Stag today - oil, cleaned intake and a/c filters, changed plugs etc, etc...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...