Jump to content
SAU Community

Recommended Posts

How'd you do the PS? Just lock to lock about 30 times?

I had to do mine, since we were pushing the car around between workshops.

Attesa Plug under the dash. 2 person job- why 3 Iain - dont need to stay in the boot!

I did PS when I did the cooler.

Drain fluid, hook up cooler, top up fluid, done. I didn't dick around with any bleeding procedures, and it works fine.

I did PS when I did the cooler.

Drain fluid, hook up cooler, top up fluid, done. I didn't dick around with any bleeding procedures, and it works fine.

You didn't drain the rack though, that's where the issue was. It takes hours to get all the air bubbles out of it.

  • 2 weeks later...

Serviced 'our' non Stagea: a 1.4 SOHC XC Barina.

What a shit job. Sump plus is some POS that needs torx to remove it. Comes off pretty easy with a hammer and chisel though!

And some genius hung the cat in front of the engine, next to the oil filter...

Now that I've had it up on the hoist though, I can see... New exhaust and manifold should do wonders, and I'm sure someone does an induction kit and chip for the Opel and Vauxhall versions. And some sway bars... Oh dear...

Dailys suck teh balls.

I'm fighting a cold idle problem on mine atm. Basically even if the car is hot, the cold idle valve still allows some air flow and I get a high idle. Doesn't help that coolant changes were negleted prior to me, and little things have corroded. Oh, and then I had to do a radiator top hose on it, and its due for a cam belt, clutch, maybe water pump, and dizzy oil seal soon too!

i got a full set of torx bits for the pair of euros i have now. its bit of a PITA that i have a full set of metric sockets and ring/open spanners that i mostly cant use on the cars

It's not the Torx that pisses me off the most, it's the cheap shit sump plug. It was already knocked about when I looked at it, and it was seized and f**ked. Torx just seems completely unnecessary to me. Allan keys ftw!

Dailys suck teh balls.

I'm fighting a cold idle problem on mine atm. Basically even if the car is hot, the cold idle valve still allows some air flow and I get a high idle. Doesn't help that coolant changes were negleted prior to me, and little things have corroded. Oh, and then I had to do a radiator top hose on it, and its due for a cam belt, clutch, maybe water pump, and dizzy oil seal soon too!

What have you got?

I'm lucky by comparison! It'll need brakes and tyres in 10,000, but other than that it's pretty good. Thinking I should replace the air filter, no one knows when it was last changed.

Hey Ryan did you wrap your roof this weekend?

Our daily is a little 1998 excel the missus bought new for 12k on road. Still going mechanically strong at 210,000km with only a clutch master, alternator and map sensor being replaced. Still runs the original clutch, brake pads and rotors that that have never needed to be machined. Pads even have 6mm thickness left. I agree not the best cars around but this one has certainly been great value with only the paint letting it down now that it's fading.

Edited by slippylotion

What have you got?

I'm lucky by comparison! It'll need brakes and tyres in 10,000, but other than that it's pretty good. Thinking I should replace the air filter, no one knows when it was last changed.

91 Mazda 323. Its a little trooper. still going great, just about to clock over 200k. One family car. Big spends have really only been a set of shocks, and a timing belt/clutch waterpump service, and reco'd shafts in 110,000kms of use. Other than that, done a rad top tank, and pipe, 2 fuel filters, 2 air filters, Gearbox fluid x1, a $14 water temp sensor, some tyres (still going great after 55,000kms! pirelli FTW!) some random relays, a coil pack/leads that weren't needed because we were trouble shooting... and oil and filter every 7000kms. Oh, and some strut top bushes- they were a bit pricey for what they were. Thats off teh top of my head.

I've taken to writing down when I last did stuff to each of them on the beer fridge now for convenience in whiteboard pen. works a treat.

I've taken to writing down when I last did stuff to each of them on the beer fridge now for convenience in whiteboard pen. works a treat.

I had a similar reminder system for my Cressida, but it was on the Rad support in permanent marker, White spirits would get most of it off when stuff needed an update.

Hey Ryan did you wrap your roof this weekend?

Our daily is a little 1998 excel the missus bought new for 12k on road. Still going mechanically strong at 210,000km with only a clutch master, alternator and map sensor being replaced. Still runs the original clutch, brake pads and rotors that that have never needed to be machined. Pads even have 6mm thickness left. I agree not the best cars around but this one has certainly been great value with only the paint letting it down now that it's fading.

Nah mate, didn't get to pick it up. Buggered up and got the night for the SAUSA dinner wrong... Will make a new time to pick it up and go again.

I've always heard good things about Excels being good value and bullet proof, not my thing though. Guess that's why the missus bought it and not you!

The XC is my woman's, if I had to buy one myself I would have got a manual at least, preferably a 1.8.

91 Mazda 323. Its a little trooper. still going great, just about to clock over 200k. One family car. Big spends have really only been a set of shocks, and a timing belt/clutch waterpump service, and reco'd shafts in 110,000kms of use. Other than that, done a rad top tank, and pipe, 2 fuel filters, 2 air filters, Gearbox fluid x1, a $14 water temp sensor, some tyres (still going great after 55,000kms! pirelli FTW!) some random relays, a coil pack/leads that weren't needed because we were trouble shooting... and oil and filter every 7000kms. Oh, and some strut top bushes- they were a bit pricey for what they were. Thats off teh top of my head.

I've taken to writing down when I last did stuff to each of them on the beer fridge now for convenience in whiteboard pen. works a treat.

That's a long time to own a car! Sounds like its been good. We had a Laser TX3 rally car at one point, which shared a lot of common parts with a 323/Familia. Good car except the gearbox...

We've got a record of what's been done in the glove box - complete service history since new. Impressive really.

  • 1 month later...

I always thought bbennys car looked great. Wonder why it keeps going up for sale though?

I'm pretty sure Ben moved it on to free up some capital for his business; I don't believe he really wanted to get rid of it. Who knows with the current owner?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...