Jump to content
SAU Community

Recommended Posts

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/343240-r33-gt-r-best-first-mod-option/
Share on other sites

remove boost restrictor,good air filter, whole exhuast with good metal cat, cam gears, boost controller max 18psi on stock comp and injectors, then comp and z32 afms, then injectors and fuel pump, turbos, cams and full engine build, i've done or in process of doing in this order

Thanks guys, much appreciated.

Some of those will have to wait until the bank account recovers from buying the car! LOL

Just curious, will I notice much of a difference if I remove the boost restrictor now?

Also how safe is this given the ceramic stock turbo wheels? And do I need a boost gauge (other than the stock one) and a manual boost controller?

from memory (tuned one awhile back and was not to far off one with 3" cat back) the std 33 GTR exhaust was not too bad at the power levels these make (JDM cats are good, compliance cats are not) boost restrictor removal and tune if your not into more noise from the rear.

Removing the bung improves your air intake... I dont know how is that bad. Plus you can hear the induction and bov sound more and its legal!

But anyway, like everyone else said. Get someone good to look after your car if you're not very mechanically minded. Probably good to get the exhaust system done first (front pipe, cat and catback) and ecu + boost (around 12-14psi should be fine on stock turbo). Read more on the force induction section and you'll find most of your questions already answered.

totally depends on budget

ensure your brakes are up to scratch first, & an oil change & spark plugs

ensure the HICAS fluid is also correct.

next i would

(assuming all is stock)

replace the factory intake - replace with ARC if budget allows or Apexi.

replace factory exhaust / muffler withi something like HKS Hi silent if your wanting a quiet muffler or blitz nur if not

take out the cat , and replace with decat

boost controller run at 1bar.

then dyno run to ensure all is well

fuel pump woudl also be on my agenda

It seems when I am reffering to the boost restrictor others are talking about something to do with the airbox etc.

I am talking about the boost restrictor that is in one of the vaccuum hoses and is marked by the yellow line. It restricts boost to 9psi from the factory and when removed raises the boost to 14psi.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

There is no HICAS fluid on a R33 or R34 the HICAS rack is electric not hydraulic. And do not waste your money on replacing intake pipes... get everything fixed and ensure everything functions correctly. That will cost you enough before you start spending it on handling better and going faster!

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

dont do it, its a slippery slope :blink:

i would personally get everything checked over, stick it on a dyno and check afr, compression if not already checked, service and replace anything thats worn like pads, rotors, tyres etc, after all that, you have a good base to start doing lil mods, i wouldnt take the restrictor out if u running stock turbos, its still a nice car, enjoy it and do the easiest and cheapest mods first so your wallet doesnt have a heart attack

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...