Jump to content
SAU Community

Recommended Posts

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/343240-r33-gt-r-best-first-mod-option/
Share on other sites

remove boost restrictor,good air filter, whole exhuast with good metal cat, cam gears, boost controller max 18psi on stock comp and injectors, then comp and z32 afms, then injectors and fuel pump, turbos, cams and full engine build, i've done or in process of doing in this order

Thanks guys, much appreciated.

Some of those will have to wait until the bank account recovers from buying the car! LOL

Just curious, will I notice much of a difference if I remove the boost restrictor now?

Also how safe is this given the ceramic stock turbo wheels? And do I need a boost gauge (other than the stock one) and a manual boost controller?

from memory (tuned one awhile back and was not to far off one with 3" cat back) the std 33 GTR exhaust was not too bad at the power levels these make (JDM cats are good, compliance cats are not) boost restrictor removal and tune if your not into more noise from the rear.

Removing the bung improves your air intake... I dont know how is that bad. Plus you can hear the induction and bov sound more and its legal!

But anyway, like everyone else said. Get someone good to look after your car if you're not very mechanically minded. Probably good to get the exhaust system done first (front pipe, cat and catback) and ecu + boost (around 12-14psi should be fine on stock turbo). Read more on the force induction section and you'll find most of your questions already answered.

totally depends on budget

ensure your brakes are up to scratch first, & an oil change & spark plugs

ensure the HICAS fluid is also correct.

next i would

(assuming all is stock)

replace the factory intake - replace with ARC if budget allows or Apexi.

replace factory exhaust / muffler withi something like HKS Hi silent if your wanting a quiet muffler or blitz nur if not

take out the cat , and replace with decat

boost controller run at 1bar.

then dyno run to ensure all is well

fuel pump woudl also be on my agenda

It seems when I am reffering to the boost restrictor others are talking about something to do with the airbox etc.

I am talking about the boost restrictor that is in one of the vaccuum hoses and is marked by the yellow line. It restricts boost to 9psi from the factory and when removed raises the boost to 14psi.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

There is no HICAS fluid on a R33 or R34 the HICAS rack is electric not hydraulic. And do not waste your money on replacing intake pipes... get everything fixed and ensure everything functions correctly. That will cost you enough before you start spending it on handling better and going faster!

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

dont do it, its a slippery slope :blink:

i would personally get everything checked over, stick it on a dyno and check afr, compression if not already checked, service and replace anything thats worn like pads, rotors, tyres etc, after all that, you have a good base to start doing lil mods, i wouldnt take the restrictor out if u running stock turbos, its still a nice car, enjoy it and do the easiest and cheapest mods first so your wallet doesnt have a heart attack

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...