Jump to content
SAU Community

Recommended Posts

it was just clumsy on Hamilton's part (again!) - yes, at one point he was in almost to the front wheel, but then half backed out and the collision was Hamilton's front wheel on Massa's rear. Its not really an overtaking area - if you're going to do it there you really need to make it a dominant move, clearly in front. He didn't. His move relied on the other driver getting the f*&% out of his way. He had to know Massa was not going to do that!

On the other hand, I feel it was pretty deliberate from Massa - he definitely saw him going up the inside but gave him the big "f*&% you"

You know its a strange call when the pommy BBC commentators are amazed that Hamilton didn't get penalised.

Edited by hrd-hr30

I completely agree Harry.

I still see it as Hamo's fault. But would like to see some GPS data to confirm it.

To my mind, Hamo needed to be much more forthright to take that position cleanly at that part of the track, and he simply wasn't.

Massa's not liable to gift him the spot is he? It's a dubious passing spot, and if Massa WAS to yield, then I reckon he would simply have to go wide into the dust, and hence, understeer off the track!

To make any pass clean and successful, the passing driver needs to have the capacity to drive his own car, but also "get his brain" into the car he wishes to pass, and decide then if the pass can be made successfully! I think even Lewis would admit (if he were honest) that he didn't do that.

the correct call was made. their front wheels were nearly level and there's no way Massa could not have known Lewis was there.

You cant really believe that!

Hamo, "I am Lewis "Victim" Hamilton...i only need to be near the back of the car in front and I should be gifted a position"

I am not sure if Massa was a little later on the brakes or if Hamo knew he wasnt far enough up the side, he was on the dirty side, he had the wrong line...err basically he had ham fisted it and was trying to get out of there. Massa has to be the most hit guy in F1 this year. Between Hamoo and Webber in Monza...he is a magnet...it seems everyone thinks he is a soft touch, including Alonso

IF Massa did back out of the corner, or run right off the track (his only 2 options to avoid contact) I doubt Hamilton would've been able to make the corner himself. With that line he would've run wide..

I was speaking to a few Hamilton fans today and even they agreed it was bullshit.

The stewards penalized the wrong party.

Lewis is right on the edge of the track and Fillipe had the whole right side of the circuit and chops him anyway. Massa could have just missed the apex like he's supposed to when someone's attempting to overtake up the inside (and is well and truly alongside). Hamo obviously trusted him to leave some racing room, and what was he supposed to do about it when Massa just jags the wheel left at the eleventh hour??

The replay doesn't show an overly ambitious overtake attempt, I feel. The stewards no doubt saw the collision as avoidable if Massa had chosen to avoid it.

Lewis is right on the edge of the track and Fillipe had the whole right side of the circuit and chops him anyway. Massa could have just missed the apex like he's supposed to when someone's attempting to overtake up the inside (and is well and truly alongside).

yeah, see there's this thing called the racing line, that you need to take to make the corner at race speed. You can't just go wider and leave room without also going slower which he wasn't. Massa's only way through that corner at that speed was the line he took. This also suggests that Dezz's observation that Hamilton probably wouldn't have made the corner either is correct. And that's before you even take into consideration the dirty surface off-line. That's why the experienced drivers we have as commentators mentioned its one at a time through that section just one lap before.

Have since heard Hamilton admit in an interview he tried to pull out of the move. Half arsed passing attempt + half arsed pull out = complete Hamfisted effort. The guy's a hack.

Yep, I don't claim to be an experienced racer/race steward, but that was one of the easier calls imo. Not sure how they got it wrong to be honest...

As mentioned already, even Brundle and DC were saying Hamilton was to blame, and we all know how much they love to smoke his pole...

Lewis is right on the edge of the track and Fillipe had the whole right side of the circuit and chops him anyway. Massa could have just missed the apex like he's supposed to when someone's attempting to overtake up the inside (and is well and truly alongside). Hamo obviously trusted him to leave some racing room, and what was he supposed to do about it when Massa just jags the wheel left at the eleventh hour??

The replay doesn't show an overly ambitious overtake attempt, I feel. The stewards no doubt saw the collision as avoidable if Massa had chosen to avoid it.

With all due respect, and you've been around a long time, but I reckon we'd go a long way to find a bigger Lewi fan boy!

Martin and David were both astonished with the stewards decision in my opinion, but they need to bite their collective tongues.

He has had far too many run-ins with Massa this year. Lewis seems increasingly frustrated with being held up by Fellipe, and Massa increasingly annoyed at Hamilton's attempts to pass.

I think the best thing to say about the incident was LH's decision to come down the inside was a tad optimistic, and FM's defense was overly aggressive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...