Jump to content
SAU Community

Recommended Posts

AH. You must have got given the non-ported version. The ported one is 34mm.

As reference my SS1PU is 29mm. Fingers crossed for Saturday.

Success - strangely it holds ~.9-1bar of boost on wastegate boost, which is more like what we expected in the first place. Mysterious, but at least it's sorted now :)

Qu O/T.

has anyone used a kando turbine housing (like the ones below) on a garrett gt30 based turbo?

http://shopping.kinugawaturbo.com/turbinehousingkinugawagarrettgt3037gt3076rgt3071rgt30rar618cm.aspx

if so, what were the results and what are your thoughts on the quality?

would you think the A/R 8cm is too small for a 2.0L 4-cyl twin-cam engine?

thanks.

Qu O/T.

has anyone used a kando turbine housing (like the ones below) on a garrett gt30 based turbo?

http://shopping.kinugawaturbo.com/turbinehousingkinugawagarrettgt3037gt3076rgt3071rgt30rar618cm.aspx

if so, what were the results and what are your thoughts on the quality?

would you think the A/R 8cm is too small for a 2.0L 4-cyl twin-cam engine?

thanks.

It doesnt fit the good gt30's any way 56t / 84 version is the way to go.

It doesnt fit the good gt30's any way 56t / 84 version is the way to go.

yes it does.

- Turbine wheel Spec : 84 Trim / 60.0 Major / 55.0 mm Exducer

- There are three types of GT3071R turbine wheel. This housing can not fit 56.5mm/trim 84 nor 56.5mm/trim 90 turbine wheel.

And this is with Link boost control turned off on the dyno, so just wastegate boost:

attachicon.gifMaxInj.png

And an interesting update since the boost creep issue has been pretty much sorted, couldn't do 3rd gear because of lack of traction (??!!!!) on 18psi - even 4th getting a bit skatey (it's around 0 degrees here tonight)... decent spool even on 80% throttle though:

post-11136-0-68171000-1373537973_thumb.png

yes it does.

- Turbine wheel Spec : 84 Trim / 60.0 Major / 55.0 mm Exducer

- There are three types of GT3071R turbine wheel. This housing can not fit 56.5mm/trim 84 nor 56.5mm/trim 90 turbine wheel.

ahh thought it said it didnt fit the 56mm 84 version... which is the only one worth using.

  • Like 1

ahh thought it said it didnt fit the 56mm 84 version... which is the only one worth using.

Interesting.. Not a fan of the 60mm 84T?

I thought the creme of the crop was the 3037 60mm 84T?

  • 2 weeks later...

I have a feeling that IWG housing is a flanged version of the fail-whale 3 bolt one. If you remember there was a guy who hacked open his fail-whale housing to make it a proper open flanged rear end (a Jez customer) and that also failed.

I would probably do this with an EWG housing like urtwhistle, or would consider a G3 with some massive v-band outlet (IWG).

I have a feeling that IWG housing is a flanged version of the fail-whale 3 bolt one. If you remember there was a guy who hacked open his fail-whale housing to make it a proper open flanged rear end (a Jez customer) and that also failed.

I would probably do this with an EWG housing like urtwhistle, or would consider a G3 with some massive v-band outlet (IWG).

yes was concerned about that...but 830 bucks :woot: and its a 12cm so maybe it'll work a little betterer

some goose tried to convince me to put a EFR turbo on it which would be awesome but jeezuuz i can almost get a 2jz half cut for the same price...

also all the budget 7m manifolds are t4 it seems...its an NA+T so 9.something compression...only aiming for low boost and responsiveness and I would prefer IG to keep it simple , not aiming for big power just a meaty midrange and good spread...g3 could work well would prefer power from 3-6rpm

Got some tree stumps need pulling

hahahah dam iphone........... If your going for low boost I wouldn't go the TD06H like I did. I would probably stick to the ordinary TD06 so that it boosts a bit quicker. I went the billet compressor wheel too so I'm not sure what difference that made. Yeah I think it was the one you said wouldn't work hahhahaha. but then again if my memory serves me correct it has a 3" surge TD07 compressor cover not the normal ones. I can't remember, it was too many bourbons ago. All I know is that when I fix all the pipes that blow off above 20psi and fuel surge it will make more power by the feel of it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...