Jump to content
SAU Community

Recommended Posts

got my remsa pads on my desk (apparently between the qfm hpx and ar1m but still low rotor wear and dust)

i really want to put them in tmrw but i also want to machine the front rotors :(

really wishing i was either in qld (my mate has lathes and stuff) or had a big lathe in my garage

I have a lathe the disks fit onto Tom but I could never hold them in the chuck well enough to face them properly, they need to be bolted/clamped in. My local bloke machines disks for $20 each anyway so I don't bother.

I have a set of Brembo's I am rebuilding at the moment, new seals etc. When he machined the Brembo disks he had to change to a carbide cutter as they were so hard. Pita for him apparently.

Another frustrating week of waiting for my Aero kit to be painted.rant.gif

Dropped in on Thursday; to see the bars in primer, looking slick as, waiting for paint!woot.gif

Hopefully they'll be on by the weekend!

The bolts that mount the sides of the rear bar (top edge) are these accessed from the boot? What trim do I need to remove to access them?

Thanks in advance.wave.gif

I have a lathe the disks fit onto Tom but I could never hold them in the chuck well enough to face them properly, they need to be bolted/clamped in. My local bloke machines disks for $20 each anyway so I don't bother.

I have a set of Brembo's I am rebuilding at the moment, new seals etc. When he machined the Brembo disks he had to change to a carbide cutter as they were so hard. Pita for him apparently.

yeah i think jap rotors > australian rotors

we did a pair of 31 rear rotors at my mates workshop over summer and they went well (any the calliper had locked on so the surface was blue = hard) and it took the surface off well, it just takes a long time to set them up and make sure they are true plus most lathes won't reach and do both sides without flipping the rotor around

so if you have to pay someone to run them on a regular lathe = exxy because its time consuming, but if you free lathing (like i do at uni banana.gif) then its kinda worth it

The bolts that mount the sides of the rear bar (top edge) are these accessed from the boot? What trim do I need to remove to access them?

yes

just the inside trim each side. dont lose any of the nuts, i dont have 100s of them spare lol

yes

just the inside trim each side. dont lose any of the nuts, i dont have 100s of them spare lol

Thanks Iain :thumbsup: Man, I need to tee up with you to pick up that arm too; totally forgot about it! You about one night this week?

Cheers, Dale.

took off the stock airbox apart, washed and cleaned the top front part (lots of dirt and gunk in there for some reason), took off part of the resonator (broke a couple of clips in the process pinch.gif), took the car out and the engine sounds louder, but wanted a bit more loud, any suggestions other than changing to pod filter?

if your wanting abit more loud without tuning, i wouldnt do this.

you would need an eManage as you'll be hitting airflow cut quite often

agree with aaron...not planning to get any piggyback ecu or anything, just want a cheap way to make the intake sound louder without using pod filter...

what about the part underneath the panel filter? can i block it somehow?

If you want more noise you can leave the top off the airbox - down side is warmer intake temps. Your choice - more noise or better performance. If you block off the bottom of the airbox the car probably won't go at all.

Hey Chris whats wheels are they? Mate of mine asked and I assumed XD9's at quick glance but they are indeed different, not to mention they don't make XD9's in 19"...

They are a CE28 copy by a company called Varrstoen.

:)

They are a CE28 copy by a company called Varrstoen.

:)

CE28! I forgot about them. Are they quality copies? I've been living in a carless world in the mountains of Canada for the last year and a bit - amazing how much has changed in the mean time lol.

CE28! I forgot about them. Are they quality copies? I've been living in a carless world in the mountains of Canada for the last year and a bit - amazing how much has changed in the mean time lol.

Varrstoen probably make one of the nicest copies going around... They actually make wheels is good size/width and offsets unlike most Chinese wheels which haven't much selection at all.

Mike

Yeah I was keen on WedsSport SA-67R's for my M35 until I realised that I'd either be cramming a 10" wheel onto my car or run a 9" wheel with spacers. I know Lense Corse do the LC818 but getting the right size is proving tricky (everyone wants to sell a staggered set).

Pics of the car yet?

Oh and today i took my car our to mallala for the g1 drift.

Drove half a lap to the start to get some different camera angles and went to start it and had no power left >_<

Getting your car jump started in front of a few thousand people on a race track is embarrassing... New battery this week methinks...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...