Jump to content
SAU Community

Recommended Posts

EDIT COMPLETE, here's my consumption

And I didn't drive it like a grandma. Keep in mind I said standard....so it was 190rwkw with standard everything except for FMIC, pod filter, JJR coilpacks, and 11psi

post-60560-0-23881400-1294225085_thumb.jpg

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

well atm i have had them for year. car idles fine, cold start always been good, makes 282rwkw on 15psi

mind u thats on a rich (11.5afr) e85 tune! re tune in a week or two for 25psi.

What Ive heard is it all depends on who does it. If they do a good job then it should be fine but also if its dodgy can be a disaster. Ive even heard of some guys freind doing it for him in hes own garage and aparently no complaints lol.

But personally I like to spend the extra and know 100percent I know what is in there is quality so in my book nismos ftw,

I just picked up from the guys at PRO-RACE a set of seimens 650cc injectors $492 ret, a top feed rail $290 ret, and a set if injector plugs from Coventrys $50 ret. I think its the cheapest way and its all brand new so you should not have any problems.

I'm personally not a fan of hi-flowed injectors, probably from one bad experience. A friend of mine had hi-flowed injectors on his 200SX and no matter what I did on the PowerFC I couldn't get A/F on idle or light cruise.

I suspect bad spray pattern, yes it will flow what you want, but it's pretty much acting like a hose spraying petrol instead of misting it.

Please note, I said from "bad experience".

i got my injectors hi-flowed by PJ Quick bits.

600cc @ 43psi

850cc @ 60psi

all flowed within 1-2cc of each other.

no issues yet with run in tune, pulled around 180rwkw @ 8psi, full tune in 1.5wks so i will report back with any issues.

I also had a set done by cef1ie and found them to work fine. Later sold them to another member and never heard back on a complaint. Cef1ie also ran the same thing in his own car to great results.

In the end I got a set of injectors back with one hole rather than 4, so it seems consistent with what was mentioned in the thread above.

ive got 740cc hi flowed injectors, not long after installing them my car developed a bad misfire from idle to 2000rpm, turned out to be inferior quality pindle caps fitted when they were high flowed, quite annoying that a 2c part ended up costing quite a bit in labour to have fixed.

my mechanic isnt a big fan of the high flows, as mentioned he reckons that when they are high flowed the spray pattern is pretty much wrecked. Idle and cold start isnt the best either, once its warm though its fine, apart from that though they do the job.

car is 214rwkw@10psi

Edited by bsd-gtst

i spoke to cef1ie and he said he doesnt touch the pindle at all just the screen so incorrect fitted pindle caps is a load of s*** so in saying that the spray pattern is not changed because the pindle is not touched

Edited by luvpsi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...