Jump to content
SAU Community

Recommended Posts

JECS is a generic manufacturer, like bosch

it would be a std item fitted to the car most likely, ie; OEM part

ok because i found some JECS 55cc injectors for rb25det so i was wondering are they anygood it does note remanufactured so does this man they are highflows however they are red tops

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5619991
Share on other sites

ive also been looking at these injectors it says they are from factory injectors does this mean they have been high flowed or just remanufactured to flow 850cc

http://cgi.ebay.com/ebaymotors/6-JECS-855cc-Fuel-Injectors-Nissan-RB25DET-_W0QQcmdZViewItemQQhashZitem3cb36e9e18QQitemZ260708408856QQptZRaceQ5fCarQ5fParts

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5621200
Share on other sites

From the advert

Remanufactured: A properly rebuilt automotive part. The item has been completely disassembled, cleaned, and examined for wear and breakage. Worn out, missing or non-functioning components have been replaced with new or rebuilt components. It is the functional equivalent of a new part and is virtually indistinguishable from a new part. See the seller’s listing for full details. See all condition definitions
Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5621239
Share on other sites

most likely they are rebuilt, high flowed injectors. your call but I would personally just buy new ones. injectors are not super expensive these days an are fairly important....

+1

and by the time you get them flow tested m, check spray patterns etc, you could have just purchased a new set anyway.

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5622488
Share on other sites

I have tested a set of sard 700s once and they were all within a bees dick of each other. never bothered again with new denso type ones (sard/nismo etc). have tested plenty of standard injectors though and found a few % variance is the norm.

Link to comment
https://www.sau.com.au/forums/topic/349955-jecs/#findComment-5622944
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...