Jump to content
SAU Community

Recommended Posts

So you what do you think of this...

SAU Member: Kris..

rb20DET

HKS 25/35 turbo rebuilt by RotaMaster

JJR 38mm external watsgate

Supertech forged pistons 20thou oversized

ARP rod bolts

ARP head studs

Cometic metal head gasket

Cometic gasket kit

nissan oil pump

nissan water pump

nissan idler pully

nissan tensioner pulley

NDC bearing kit

HKS camshafts, 264/8.5mm

HKS cam gears

Gates timing belt

Tridon thermostat

crank was grub screwed, balanced and ground

balanced pistons

balanced and resized rods

block was decked, bored and honed

resurfaced head

valve grind

new valve stem seals

exhaust guides and ports cleaned up a bit

braided lines

GReddy returnflo front mount intercooler kit

Gkteck dump and front pipe

Blitz cat back

Splitfire coilpacks

JJR alloy radiator

z32 AFM

GTR injectors and resistor pack

Status remaped ECU

Walbro fuel pump

JJR oil cooler relocation kit

gutted cat

238rwkw @ 19psi

Me

Full RB20DET rebuild with upgraded rods and bearings (nothing forged as far as I know)

FMIC

Full turbo back exhaust with performance cat

Greddy Dump Pipe

z32 AFM

Cold air intake

Splitfire coilpacks

550cc injectors

Stock ECu remap

Garrett GT2871R

Bosch 044

Exedy Super HD Clutch

230.3rwkw @ 16psi Dyno Sheet R32 GTS-T.pdf

So the guy above threw 3 x as many mods into his 32 as me and only has 8 more rwkw and is running 3 psi more boost.

Can anyone explain this???

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/
Share on other sites

Oh dude for crying out loud. Some reading before posting helps!

Every setup is different

Every dyno is different

Every tune is different

Every persons location is different (and this climate can be a factor in tunes)

You want any more possibilities?

Dyno results are a good guide, but to split hairs over 8rwkw is pointless.

If the dyno he is on, reads 10rwkw low, and yours reads 10rwkw high, then all of a sudden its 28rwkw.

You'll NEVER KNOW.

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635828
Share on other sites

Well that turbo would be prety close to being maxed out so its no matter what you do youll be struggling to go over with a 2535. At the end of the day you can have a full built motor with everthing you could possibly want on it and what would happen if you put a stock turbo? You wont make power.

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635838
Share on other sites

So the guy above threw 3 x as many mods into his 32 as me and only has 8 more rwkw and is running 3 psi more boost.

Can anyone explain this???

Different turbos, different tuner, different dyno.. unsure but his could make alot more power if the boost is wound up more.

also he seems to have done it the right way to make it all last and you seem to have the best turbo for your power range..

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635839
Share on other sites

Oh dude for crying out loud. Some reading before posting helps!

Every setup is different

Every dyno is different

Every tune is different

Every persons location is different (and this climate can be a factor in tunes)

You want any more possibilities?

Dyno results are a good guide, but to split hairs over 8rwkw is pointless.

If the dyno he is on, reads 10rwkw low, and yours reads 10rwkw high, then all of a sudden its 28rwkw.

You'll NEVER KNOW.

So why do we compare tunes then? If everything is subject to error/accuracy issues.

Why do you have a power thread to compare tunes? Why don't we tell everyone to do exactly the same mods and use exactly the same dyno at exactly the same temperature at exactly the same altitude at exactly the same geographic position at exactly the sime time of day.

Way to put a dampener on my day nismoid.

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635845
Share on other sites

So you what do you think of this...

SAU Member: Kris..

rb20DET

HKS 25/35 turbo rebuilt by RotaMaster

JJR 38mm external watsgate

Supertech forged pistons 20thou oversized

HKS camshafts, 264/8.5mm

HKS cam gears

GReddy returnflo front mount intercooler kit

Gkteck dump and front pipe

Blitz cat back

Splitfire coilpacks

JJR alloy radiator

z32 AFM

GTR injectors and resistor pack

Status remaped ECU

Walbro fuel pump

238rwkw @ 19psi

Me

Full RB20DET rebuild with upgraded rods and bearings (nothing forged as far as I know)

FMIC

Full turbo back exhaust with performance cat

Greddy Dump Pipe

z32 AFM

Cold air intake

Splitfire coilpacks

550cc injectors

Stock ECu remap

Garrett GT2871R

Bosch 044

Exedy Super HD Clutch

230.3rwkw @ 16psi Dyno Sheet R32 GTS-T.pdf

So the guy above threw 3 x as many mods into his 32 as me and only has 8 more rwkw and is running 3 psi more boost.

Can anyone explain this???

i just removed the things that wouldnt effect overall power. he has 2 more mods then you. i could simplify the engine work by grouping it under "rebuilt engine" and im pretty sure it will be the same.

you pretty much have the same amount/type of mods but he is pulling more power.

peace out.

Edited by SECURITY
Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5636257
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • Thank you so much for the help
×
×
  • Create New...