Jump to content
SAU Community

Recommended Posts

So you what do you think of this...

SAU Member: Kris..

rb20DET

HKS 25/35 turbo rebuilt by RotaMaster

JJR 38mm external watsgate

Supertech forged pistons 20thou oversized

ARP rod bolts

ARP head studs

Cometic metal head gasket

Cometic gasket kit

nissan oil pump

nissan water pump

nissan idler pully

nissan tensioner pulley

NDC bearing kit

HKS camshafts, 264/8.5mm

HKS cam gears

Gates timing belt

Tridon thermostat

crank was grub screwed, balanced and ground

balanced pistons

balanced and resized rods

block was decked, bored and honed

resurfaced head

valve grind

new valve stem seals

exhaust guides and ports cleaned up a bit

braided lines

GReddy returnflo front mount intercooler kit

Gkteck dump and front pipe

Blitz cat back

Splitfire coilpacks

JJR alloy radiator

z32 AFM

GTR injectors and resistor pack

Status remaped ECU

Walbro fuel pump

JJR oil cooler relocation kit

gutted cat

238rwkw @ 19psi

Me

Full RB20DET rebuild with upgraded rods and bearings (nothing forged as far as I know)

FMIC

Full turbo back exhaust with performance cat

Greddy Dump Pipe

z32 AFM

Cold air intake

Splitfire coilpacks

550cc injectors

Stock ECu remap

Garrett GT2871R

Bosch 044

Exedy Super HD Clutch

230.3rwkw @ 16psi Dyno Sheet R32 GTS-T.pdf

So the guy above threw 3 x as many mods into his 32 as me and only has 8 more rwkw and is running 3 psi more boost.

Can anyone explain this???

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/
Share on other sites

Oh dude for crying out loud. Some reading before posting helps!

Every setup is different

Every dyno is different

Every tune is different

Every persons location is different (and this climate can be a factor in tunes)

You want any more possibilities?

Dyno results are a good guide, but to split hairs over 8rwkw is pointless.

If the dyno he is on, reads 10rwkw low, and yours reads 10rwkw high, then all of a sudden its 28rwkw.

You'll NEVER KNOW.

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635828
Share on other sites

Well that turbo would be prety close to being maxed out so its no matter what you do youll be struggling to go over with a 2535. At the end of the day you can have a full built motor with everthing you could possibly want on it and what would happen if you put a stock turbo? You wont make power.

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635838
Share on other sites

So the guy above threw 3 x as many mods into his 32 as me and only has 8 more rwkw and is running 3 psi more boost.

Can anyone explain this???

Different turbos, different tuner, different dyno.. unsure but his could make alot more power if the boost is wound up more.

also he seems to have done it the right way to make it all last and you seem to have the best turbo for your power range..

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635839
Share on other sites

Oh dude for crying out loud. Some reading before posting helps!

Every setup is different

Every dyno is different

Every tune is different

Every persons location is different (and this climate can be a factor in tunes)

You want any more possibilities?

Dyno results are a good guide, but to split hairs over 8rwkw is pointless.

If the dyno he is on, reads 10rwkw low, and yours reads 10rwkw high, then all of a sudden its 28rwkw.

You'll NEVER KNOW.

So why do we compare tunes then? If everything is subject to error/accuracy issues.

Why do you have a power thread to compare tunes? Why don't we tell everyone to do exactly the same mods and use exactly the same dyno at exactly the same temperature at exactly the same altitude at exactly the same geographic position at exactly the sime time of day.

Way to put a dampener on my day nismoid.

Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5635845
Share on other sites

So you what do you think of this...

SAU Member: Kris..

rb20DET

HKS 25/35 turbo rebuilt by RotaMaster

JJR 38mm external watsgate

Supertech forged pistons 20thou oversized

HKS camshafts, 264/8.5mm

HKS cam gears

GReddy returnflo front mount intercooler kit

Gkteck dump and front pipe

Blitz cat back

Splitfire coilpacks

JJR alloy radiator

z32 AFM

GTR injectors and resistor pack

Status remaped ECU

Walbro fuel pump

238rwkw @ 19psi

Me

Full RB20DET rebuild with upgraded rods and bearings (nothing forged as far as I know)

FMIC

Full turbo back exhaust with performance cat

Greddy Dump Pipe

z32 AFM

Cold air intake

Splitfire coilpacks

550cc injectors

Stock ECu remap

Garrett GT2871R

Bosch 044

Exedy Super HD Clutch

230.3rwkw @ 16psi Dyno Sheet R32 GTS-T.pdf

So the guy above threw 3 x as many mods into his 32 as me and only has 8 more rwkw and is running 3 psi more boost.

Can anyone explain this???

i just removed the things that wouldnt effect overall power. he has 2 more mods then you. i could simplify the engine work by grouping it under "rebuilt engine" and im pretty sure it will be the same.

you pretty much have the same amount/type of mods but he is pulling more power.

peace out.

Edited by SECURITY
Link to comment
https://www.sau.com.au/forums/topic/351213-what-the/#findComment-5636257
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
×
×
  • Create New...