Jump to content
SAU Community

Recommended Posts

Updated.

Got a bran new apexi data logit that im looking to sell as im thinking of selling my power fc too.

Its so new i havent even plugged it in and used it yet. Comes complete with everything needed to use the program.

$300 I can post if need be at your expence.

RB25DET exhaust manifold. Due to a GTSR manifold i no longer need. $100

RB25DET standard injectors with out rail. Upgraded to larger items. $100

RB25DET inlet manifold. Doesn't come with throttle body or tps. Going ffp so i no longer need. $80

RB20 xtreme clutch and flywheel. Upgraded so no longer need. $150

RB25 freshly mechined flywheel. Upgraded to a molly item. $100

All items are for a S2 motor. If serious please pm me.

Adam

gt2871r .64 dual ball bearing turbo. oil and water cooled.

tial 38mm external gate set up on an sr20 stock manifold with a plumb back screamer into a 3 inch dump and front pipe.

awesome upgrade for any sr20.

turbo is mint, only around a year old. $1400 new.

i am asking 1200 ONO for the whole set up. (wont come with turbo lines it only has an oil drain)

so turbo, wastegate, manifold, dump & front pipe. o2 sensor. few bolts and gaskets if there any use.

selling due to wanting a kando

post-86412-0-07388900-1359536027_thumb.jpgpost-86412-0-51646500-1359536029_thumb.jpgpost-86412-0-45757800-1359536035_thumb.jpg

PM me your number and i will contact you thanks

Hey guys,

I have a brand new set of Pirelli P7's (still have labels on them ) and they are 215/55 r17 94v http://www.collierau...rsale/tyres.jpg , I am after $600 for these Pirelli's which ends up $150 a corner, pretty good for Pirelli's huh ?

Then I have ROH Boost R 17" rims that are in pretty good knick, the car is parked in a akward spot so I could only grab a picture of one of the rims tonight (will update with more) but the two front have Altimax HP 215/45 r17's and the rears have Rapid p609 215/45 r17 with about 85% tread on the both . One of the rims pictured http://www.collierau...forsale/Rim.jpg . I am after $800 for the wheels as the tread on them is almost new and there is barely any gutter rash on these rims at all .

PM if your keen, I am interested in grabbing some cheap stockies if anybody is getting rid of some so the car has something to sit on if you buy the rims.

Items:

R33 4 stud space saver spare tire, Never used. $30

Stock R33 front and rear sway bars $20 each

2 x 235/45/R17 firestone tires, camber wear, one has a nail in it. easy repair, 4-5mm tread left. $20 for the pair

R33 air intake snorcle $10

R33 Non turbo MAF $30

R33 series 1 ignitor pack $15

R33 series 1 coil packs x 6 $10 each or $50 for the lot

12 inch moulded sub box for the drivers side of the boot, covered in grey carpet. $50

R33 series 1 non turbo ECU $40

R33 series one front bar $50

R33 series one wing ( LED brake light doesnt work) $40

R33 power steering tank $15

R33 series one auto gear box ( came out of a type s) $50

R33 cam seal x1 new

R33 stock cam cover $20 SOLD PENDING PAYMENT

R33 stock coil pack cover $20

R33 Aluminium pod filter cover $15

R33 charcol canister $5

R33 battery - holds charge, good condition $30

R33 window washer bottle - no pumps included $5

R33 rear cabin vent - the one in the drivers side rear fender $5

No swaps.

Extra Info:

Pick up only on all large parts. Will post smaller items

Contact Details:

PM me

I have here a very rare Genuine R32 GTR front bar with lip and mesh in its original form

Bumper has a few scratches (see photos) but is otherwise in very good condition. Lip is in excellent condition and has most of the retaining clips/bolts. These are frequently missing or broken on most bumpers. It also has the factory mesh which is equally hard to find.

Bumpers being this rare I'm really after a decent price so let me know what you have in mind :)

Contact Me On

Mob:0424290504

Email:[email protected]

From Melbourne

Thanks Justin!

post-61379-0-06893700-1359615423_thumb.png

post-61379-0-74895200-1359615464_thumb.png

post-61379-0-00838200-1359615476_thumb.png

post-61379-0-93089800-1359615488_thumb.png

post-61379-0-04275100-1359615501_thumb.png

post-61379-0-49552900-1359615513_thumb.png

skyline_house

1. Please advertise a price - this is a forum rule - this is not Ebay.

2. What are you doing posting in the SA 'for sale' thread? Please post in the general 'for sale' thread in future

Kicker sub and amp in a proper kicker ported box, plus full wiring kit. Pretty sure JBs still sell this same model for around ~$300 for sub alone.

Good kit, minimal use, only selling because I don't need it anymore. $250.

img5306th.jpg

Bride drivers side, fixed rail (has two adjustments though) Came off a Stradia in a R32, believe the rail will also fit s13/180 etc. $100

img5303p.jpg

Straight pipes, twin 3". $80

img5301t.jpg

Some random brand podfilter with heat shield, think it's a 4", brand new unused. $20

img5302u.jpg

Swing me a PM/text 0431308647.

Located in Mount Barker SA.

Cheers,

Chris

Edited by XXXI

I've got a pair of SAAS sport seats in black. These have never been used - we bought them last year but didn't get around to installing them. They are black fabric / mesh. They recline & tilt forward (for access to the back seat in a 2 door), and come with sliders but no mounts.

I'd like to sell them for $160 each or $300 for the pair. They look just like this one (not the actual seat in the photo):

http://dl.dropbox.com/u/64688547/Saas%20seat.jpg

Ph 0418 841 730

I have a set of 17" winter tread tyres that were on a set of rims I bought. The fronts are 225/50R17, and have heaps of tread left. the rears are 235/50R17, and are still well above legal tread. I drove around town on these for about 6 weeks while I was painting (mostly thinking about painting) my other rims, and they are fine.

http://dl.dropbox.com/u/64688547/2013-02-01%2015.07.44.jpg

these would be good for someone needing cheap tyres, or for burnout tyres. Looking for $60 for the set.

0418 841 730

I've got a pair of SAAS sport seats in black. These have never been used - we bought them last year but didn't get around to installing them. They are black fabric / mesh. They recline & tilt forward (for access to the back seat in a 2 door), and come with sliders but no mounts.

I'd like to sell them for $160 each or $300 for the pair. They look just like this one (not the actual seat in the photo):

http://dl.dropbox.com/u/64688547/Saas%20seat.jpg

Ph 0418 841 730

Mate no offence autobarn sells the new model of that one for 149ea now

I have a set of 17" winter tread tyres that were on a set of rims I bought. The fronts are 225/50R17, and have heaps of tread left. the rears are 235/50R17, and are still well above legal tread. I drove around town on these for about 6 weeks while I was painting (mostly thinking about painting) my other rims, and they are fine.

http://dl.dropbox.co...%2015.07.44.jpg

these would be good for someone needing cheap tyres, or for burnout tyres. Looking for $60 for the set.

0418 841 730

Tyres sold

Selling some parts from my R34 GTT since upgrading:

Rear suspension | R34 GTT (fork type) - JIC Magic (Left seems to have lost pressure), otherwise excellent condition, no rubber cracks at all - $200

Stock internal fuel pump, excellent condition - $50

Stock air flow meter, excellent condition - $50

Stock cat converter, excellent condition - $50

Stock mirrors in gloss black, great condition but right mirror is missing the plastic that connects to door - $50

Return flow intercooler 600x240x60, excellent condition - $200

Rear seat belts with coils, excellent condition - $50

Rear stock seats, slight staining on seats but can probably be cleaned - $150

Stock right head light, none xenon, broken clips and floating clear plastic bit on inside - $200

Give me a text on 0431516718, pick up from Crafers in the hills (fun drive up eagle on the hill!), I can MMS any pictures required.

Items:

Hey guys i have a set of R32 GTR seats and seat rails available.

Item Condition:

Passenger seat in mint condition, driver seat in very good condition appart from 2 small tears where the seats get worn naturally, easy fix.

Contact Details:

PM me on here or sms or call on 0425 878 255

Price and price conditions:

$500 ono

Will upload pics tomorow or tues as my camera is being a ass!

R33 KYB 8 step damper adjustable coilovers, ran them in my car for 3 days and discovered the front right has a bit of a squeak, I've been told that greasing or removing the helper springs would help with this.

$450 PM me if you're interested.

post-63773-0-48905600-1359934517_thumb.jpg

s13 and 180 parts for sale

t28 turbo 300 ono

spaghetti manifold for a ca18 200 ono includes brand new gaskets

nismo dump pipe 200 ono can include brand new o2 sensor for an extra 60

FMIC kit jap brand 250 ono can include gfb bov for extra 100

ca18 afm 70

r33 gtst red guards 50 bucks for 2

front strut brace 100

PM for pics thanks

gt2871r .64 dual ball bearing turbo. oil and water cooled.

tial 38mm external gate set up on an sr20 stock manifold with a plumb back screamer into a 3 inch dump and front pipe.

awesome upgrade for any sr20.

turbo is mint, only around a year old. $1400 new.

i am asking 1200 ONO for the whole set up. (wont come with turbo lines it only has an oil drain)

so turbo, wastegate, manifold, dump & front pipe. o2 sensor. few bolts and gaskets if there any use.

selling due to wanting a kando

post-86412-0-07388900-1359536027_thumb.jpgpost-86412-0-51646500-1359536029_thumb.jpgpost-86412-0-45757800-1359536035_thumb.jpg

PM me your number and i will contact you thanks

t28 sold,

spaghetti manifold sold

dump pipe sold

ca18 afm sold

strut brace sold

2871 turbo kit sold

still got r33 guards, fmic kit, bov, o2 sensor

copied from gumtree -

will have more ca18 parts as I start to wreck my car in about 2 weeks time. So I will have a ca18det engine. will be parting all the bolt ons out and selling the engine as a bare engine.

so i have ...

manual gearbox

tailshaft

loom

ecu

coil pack cover

intake manifold

power steering pump

one CA18 fan and shroud, and an sr20 one

engine mounts

anything else that you can think of that is a ca18 bolt on

new gates timing belt on engine, idler bearings and tensioner, new oem head gasket

parts that are sold from engine

turbo

manifold

dump pipe

alternator

turbo lines

will have prices for the rest of the parts when they are out of the car.

Can hold parts for a deposit.

R32 GTR Parts

1: R32 GTR stock prop shaft $120

2: R32 GTR stock castor arms $60

3: R32 GTR eye level brake light $40

4: R32 GTR Ashtrays (both textures) one on left is broken bottem left $20 each

5: R32 GTR centre console with rear ashtray $30

6: R32 GTR twin turbo pipe painted flat black $80 or $140 with intercooler pipes.

7: R32 GTR intercooler pipes $60 or $140 with twin turbo pipe painted Flat Black.

8:‎ 8x RB26DETT Coil Packs, all work as far as I know $80.

9: R32 GTR Stock dump pipes $60.

10: RB26DETT Stock Cam Gears, 2 sets from 32 motor 1 set from 34 motor $30 a pair.

180sx parts

1: 180sx stock rear camber arms $40

2: 180sx stock castor arms $40

3: 180sx stock rear toe arms (I think) $30

4: 180sx tool kit $30

5: 180sx centre console with 3 ash trays (Including rear) $40

6: 180sx (I think)) fan $30

7: 180sx Interior lights $30 each or $50 for both

8: 180sx rear wiper motor $40

9: 180sx Steering collum trim $30

10: 180sx Whiteline adjustable sway bar links never used $50

Other parts

1: Single Din missle switch $20

2: Bonnet key locks never used $40

Some pics to big to upload

Located :Noarlunga but work down in Wayville.

Txt me on 0433 522 234 for further info and pics

Bump

Just a few parts for sale left over from conversion

S13 powr steering pump ca18 $50

R32 turbo with actuator $50

R33 smic $20

R34 gtt smic $40

S13 headlights projector sr type $10 ea

Will swap any of these parts for an s13 alt/starter lower loom or s13 tailshaft centre bearing bracket

Message ali on 0423789155

Located at 5162

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...