Jump to content
SAU Community

Valve Guides

marksuxass

By marksuxass,
in Engines & Forced Induction

 Share

Recommended Posts

r33_racer Grand Master

r33_racer

Posted
Posted

You can use 2P cast iron round bar as a good replacement material to make guides. Weve also made some guides from phosphur bronze which were currently using. However, the last set which was made by another machine shop wore out extremely fast like Daniel is saying.

Its weird how in some engines they wear out quicker then normal. Our midget engine uses phosphur bronze guides and its a push rod engine that revs to 8500rpm and has been racing for two seasons with no valve guide wear and being push rod its subject to more valve side loads then an over head cam valve....its my understanding that virtually all speedway engines run bronze valve guides and are mostly push rod. Our mates engine has run 4 years with bronze guides with minimal wear.

Weird!

bigmikespec Veteran

bigmikespec

Posted
Posted

Yes it is wierd, I am sure clearnaces between the stem and the guide would play a big part in it too. Just doing some reading I would rather use a bronze type guide for its heat transfer properties but not if they are wearing out quickly!

I asked Ferrea again about the seats but this is what they said about the guides. "a good manganese bronze or a copper bronze mix"

  • 9 months later...
bigmikespec Veteran

bigmikespec

Posted
Posted

Ok, digging up and old thread... going with a bronze manganese valve guide. How have guys gone using Supertech valve guides? Good product? Any issues?

Alternately may get NITTO valve guides but I cannot justify the price difference unless there is a good reason!

  • 4 years later...
MJTru Mentor

MJTru

Posted
Posted

Ok, digging up and old thread... going with a bronze manganese valve guide. How have guys gone using Supertech valve guides? Good product? Any issues?

Alternately may get NITTO valve guides but I cannot justify the price difference unless there is a good reason!

Sorry to wake up this old thread. But one of my stock motors rb26 just failed. Well let me start from the beginning. The motor came in a old r32 i had wit about 85k on the clock relatively new, but i know the owner and hes a guy that doesnt change oil on time and so when i got the car the motor had a spun bearing on number 3 cylinder. So i replaced l all the rods pistons with stock ones new rings and bearings new oil pump. The head o did myself and the only thing i didnt check was the guild clearance. Sad. I lap them myself as I've done this for years and all work well. Shim the buckets and all. The motor ran a cheap hoset hx35 wit l all ebay cheap stuff. Stock injectors and power fc.

It lived for 1 year. I was expecting the oil pump collar to fail but after opening it up i found one valve guild fails on the intake side one cylinder number 4 and i can see 4 more guilds have cracked. Its not to bad of a damage, but bad enough for me.

Question can worn giulds lead to them breaking. ??? Can fuel cut cause it.

Im now going to build it with a new head. I just cant get my head around what would cause it to fail. As its my first time experiencing a guide failure.

So you've pulled the head off and checked the guide clearance?

How much were the Nissan ones mate?

I just put brand new Nissan ones in. Pretty cheap.

mico Proficient

mico

Posted
Posted

Standard guides are dodgey and dangerous as, and brittle get rid of them. Ebay sells supertech guides for 264 bucks delivered can't go wrong. My guides leaked for years and I could never find why my car blew smoke but when the guides were removed they came out in pieces ....

mico Proficient

mico

Posted
Posted

Standard guides are dodgey and dangerous as, and brittle get rid of them. Ebay sells supertech guides for 264 bucks delivered can't go wrong. My guides leaked for years and I could never find why my car blew smoke but when the guides were removed they came out in pieces ....

HarrisRacing Proficient

HarrisRacing

Posted
Posted

This is true. 2 of my factory guides had chipped and broken off previously in my R32 (which had Rod knock when I bought it). As a mechanical engineer I see no issue with high strength / hardness aluminum bronzes. Remember not all bronzes are created equal just like not all cast irons are created equal.

BC guides I have used in past builds have had excellent performance for me personally. The mistu 4g63 as well as the Toyota 3sgte engines i built for my past racecars are both still living healthy lives after many seasons of racing. I would really have to spec an alloy for me to send the job to just any machine shop.

A bronze is an alloy of copper and other metals, most often tin, but also aluminium and silicon.

Aluminium bronzes are alloys of copper and aluminium. The content of aluminium ranges mostly between 5-11%. Iron, nickel, manganese and silicon are sometimes added. They have higher strength and corrosion resistance than other bronzes, especially in marine environment, and have low reactivity to sulfur compounds. Aluminium forms a thin passivation layer on the surface of the metal.

About BC guides:

RB26 VALVE GUIDES

BC premium valves guides are made from Manganese Silicon Aluminum Bronze alloy and CNC machined to exacting tolerances. BC guides are resistant to cracking and corrosion, while reducing friction and insures high lubrication even at elevated engine temperatures and rpm's. The perfect replacement to worn or damaged guides and 100% compatible with BC's lineup of stainless steel valves.

MJTru Mentor

MJTru

Posted
Posted

This is true. 2 of my factory guides had chipped and broken off previously in my R32 (which had Rod knock when I bought it). As a mechanical engineer I see no issue with high strength / hardness aluminum bronzes. Remember not all bronzes are created equal just like not all cast irons are created equal.

BC guides I have used in past builds have had excellent performance for me personally. The mistu 4g63 as well as the Toyota 3sgte engines i built for my past racecars are both still living healthy lives after many seasons of racing. I would really have to spec an alloy for me to send the job to just any machine shop.

A bronze is an alloy of copper and other metals, most often tin, but also aluminium and silicon.

Aluminium bronzes are alloys of copper and aluminium. The content of aluminium ranges mostly between 5-11%. Iron, nickel, manganese and silicon are sometimes added. They have higher strength and corrosion resistance than other bronzes, especially in marine environment, and have low reactivity to sulfur compounds. Aluminium forms a thin passivation layer on the surface of the metal.

About BC guides:

RB26 VALVE GUIDES

BC premium valves guides are made from Manganese Silicon Aluminum Bronze alloy and CNC machined to exacting tolerances. BC guides are resistant to cracking and corrosion, while reducing friction and insures high lubrication even at elevated engine temperatures and rpm's. The perfect replacement to worn or damaged guides and 100% compatible with BC's lineup of stainless steel valves.

Here is a question for you guys. I have a big build right now that i used a brand new cylinder head from nissan for. (NOT THIS ONE) But i didnt change the guides as the head was new. Here is the question do you guys know if the older oem heads and the newer one are the same guide wise. Did nissan upgrade the newer made heads with better guides than the older stuff. I would figure as time goes by the stuff would get better.

Also can you provide the part number for BC valve guides for rb26. I have a strong feeling im going to pull the new motor apart as i hate when guides fail, they do lots of damage.. i will also search for the bc part number im just wonder if yours and what i find will line up. Good info. Hats off to you mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...