Jump to content
SAU Community

Recommended Posts

$60 for the whole kit including Ballast's? or just the uni globes?

I've noticed though, anything really above 6500k your Visuality just goes downhill, especially in rain.

I'm sticking with the factory 4300ks...I had 6000k aftermarket ones in my mazda 3 and it sucked ass in the rain/mist/fog...

took like 10mins to change the parkers didnt even have to take the wheels off........... looks SO much better now :D

Wish I had your small ass hands....

Mine are now LED- hope I never have to change them again.

Wish I had your small ass hands....

Mine are now LED- hope I never have to change them again.

i still jacked the car up just so the wheel was slightly off the ground HAHA

pretty sure my disc's need a good machining they dont feel the best under heavy braking or highway driving

whats the stock brake thickness so i can see if its just worth sourcing some vented disc's.............

Maybe I missed you stating so in the past (or just forgot), but I just noticed the Nismo rear wing on your car!

Subtle, but adds just enough :)

so its a nismo wing :) i love the wing looks weird without it imo

The stock disks are 22mm new, 20mm minimum if I remember right.

32 gtr disks are 32mm new, 30mm minimum, well worth the upgrade.

just measured my disc's there 296mm X 24mm.......... minimal wear on them, doesnt look warped but the surface from outter to inner is a bit wobbly

whats the best value upgrade...................???

** just found this:

Stock- 296 x 24mm fronts

R32 GTR non vspec - 296x32

R33 GTR - 324mmx30mm

350Z Brembo pack - 324mmx30mm

Edited by WAGON_BOY

just measured my disc's there 296mm X 24mm.......... minimal wear on them, doesnt look warped but the surface from outter to inner is a bit wobbly

whats the best value upgrade...................???

** just found this:

Stock- 296 x 24mm fronts

R32 GTR non vspec - 296x32

R33 GTR - 324mmx30mm

350Z Brembo pack - 324mmx30mm

R32 GTR non vspec - 296x32 will be the cheapest, anthing with "Brembo" written on it for a Skyline seems to demand telephone number pricetags; even if they've been thrashed to death.

Another option you have is R32 GTST calipers,324x30mm 350Z brembo discs and an offset bracket from conceptz perfomance or Ebay.

The advantage with the three you've quoted is the bolt on nature of them; only some simple bushes for R32 non- Brembo.

sweet ill check out concept z perfomance :D

Try this.:thumbsup: Quoted me roughly $150 to ship to my address.

http://www.conceptzp...158.165.206.187

Edited by Daleo
  • 5 weeks later...

thinking about doing a dump pipe back exhaust soon....... basically i want to do it right the first time, whats required to be able to flow enough for 300kw@w ???

got one of Scotty's dumps already.....

striaght throught 3" system or a 3.5"???

with a 4" rear muffler or whats the go???

cheers :)

Any of the big name Jap exhaust will do the job.

Fujitsubo Legalis R

Kakimoto

Blitz Nur spec

Nismo

HKS Demodo

plus probably a few others...I think all of the above are 3" systems...not 100% sure

Edited by ironpaw

kakimoto is 80mm 3.25"

i got it. its the best ive seen to be honest(may be biased as this is what i have) and its not too loud at all.

mines flowing so much its causing the turbo to creep with my highflow.. so if you highflow it. please make sure you get a new wastegate flap and widen the wastegate hole to suit.

im talking from experience.

lol

Any of the big name Jap exhaust will do the job.

Fujitsubo Legalis R

Kakimoto

Blitz Nur spec

Nismo

HKS Demodo

plus probably a few others...I think all of the above are 3" systems...not 100% sure

Nup, the new Nismo is not 3"... nor is the Demoda for that matter.

Both 2.5" if memory serves me correctly.

Fuji Legalis and the Original M35 Nismo are 76mm and have basically the same design (very different muffler though)

Kakimoto (R or N1) and Blitz are 80mm

Demoda is rubbish for performance.

Charlestone exhaust....keeping it Local....I have had no probs with Hp development!!!

Unless if cause you want to flip your car to show shiny shot off!

Edited by Jetwreck

gonna get it made locally probly will a 100 cell cat, hotdog and resonater and muffler.

probly go with a magnaflow system............. other options are lukey and xforce

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...