Jump to content
SAU Community

Recommended Posts

Just wondering what everyone's running on their boats.

When I had new KU31's put on (245/40/18) my steering went all heavy and crap at low speed. At first I thought the tyres must be underinflated...

Went to the servo, fronts were at 34 and rears at 36. Pumped all 4 to 39(!) Is this too high?

Now I realise the increased tyre width probably has more to do with it....right?

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

read the pressure rating of the tyre. it will have a maximum. but too high will cause excess wear in the centre, an underinflated tyre will wear onthe outside.

a too firm tyre will be bumpy, especially with aftermarket suspension. i think i run mine at 38 front and 36 rear. but this is when cold. always check when cold

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749475
Share on other sites

I was runing 34psi but after a run down Putty road on the weekend it was too rough with the coil overs. So on the return trip, i lowered em to 28psi. Car was much better to drive and not quiet as rough. Still handled the corners beautifully!!

I run these tyres: http://www.falkentire.com/Tires/Passenger-Car/Azenis-RT-615K-14

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749569
Share on other sites

i like that test.

but yep, i run 38 front and rear - tested when cold.

good investment is a digital pressure gauge. dont trust the ones at the servos. i check pressures weekly. car feels nicer and less jittery over low speed bumps when the pressure is down around 36 (which is what most tyre places will reccommend) but i reun a slightly higher pressure to protect the wheels, and to counter some of the camber wear by rounding the center of the contact patch.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749929
Share on other sites

Just wondering what everyone's running on their boats.

When I had new KU31's put on (245/40/18) my steering went all heavy and crap at low speed. At first I thought the tyres must be underinflated...

Went to the servo, fronts were at 34 and rears at 36. Pumped all 4 to 39(!) Is this too high?

Now I realise the increased tyre width probably has more to do with it....right?

I run 38 - 40psi but I believe your heavy steering is caused by the wider rims/tyres and different offset. It gets worse the wider you go.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749977
Share on other sites

That's all horribly low for low profile 18's...

I run my 235/40/18's at 45psi cold, even 42psi doesn't feel right and anything under 40psi feels terrible.

You must have good suspension to compensate your tyres which are as hard as concrete!!

Must be bloody slippery in the wet/rain with those pressures.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750078
Share on other sites

50psi!? that is ridiculous. and why would you run it higher if you're lashing it? should be running it lower if anything. otherwise it just turns into a roller skate - you will get better grip with lower pressure, plus it will allow for expansion of the air as the increased heat levels build.

only people i know who run those pressures are the VIP guys who run super stretched tyres and huge camber - helps prolong tyre life and keeps the tyre seated on the bead.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750128
Share on other sites

50psi!? that is ridiculous. and why would you run it higher if you're lashing it? should be running it lower if anything. otherwise it just turns into a roller skate - you will get better grip with lower pressure, plus it will allow for expansion of the air as the increased heat levels build.

only people i know who run those pressures are the VIP guys who run super stretched tyres and huge camber - helps prolong tyre life and keeps the tyre seated on the bead.

no

Should mention, I don't have a stagea and just realised this is the stagea section..

Edited by Ten Four
Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750145
Share on other sites

on drift days you run a higher pressure in the rear. also some tyres are rated to 50psi. i remember a set i had on my S13, 52psi was the maximum. i ran them at 44psi.

if 50psi is over the maximum rating, youre taking a risk IMO

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750151
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
    • Dang, those BBS are so nice! 
×
×
  • Create New...