Jump to content
SAU Community

Recommended Posts

With regard to these Walbro E85 pumps are people having issues with them circulating too much fuel and getting hot fuel and tank pressurisation as a result of it ? Just curious to know what happens in warm weather and traffic driving .

Also does anyone have pics of one mounted to an R33s bracket ?

Lastly noise , my 25T is not particularly noisy and I can hear my 33 GTR pump whining away .

I run E70 and don't think I'd ever see more that 320 kw , Nismo is probably the easiest and quiet but you pay for it .

Cheers Adrian .

I just fitted an e85 Walbro 460 into a V8 Soarer, I could barely hear it. If you instal it correctly it will be quieter than most pumps out there, including the Nismo/Tomei.

My twin 255 setup definitely heats the fuel on hot days, within two or three hours. No issues with the tank, just the pumps get a little noisy, and a little rail evaporation I think which makes re-starting take a little longer.

I just wonder about this hot fuel business with high Eth fuels because it obviously wants to boil a little more easily . The old Bluebird converted to EFI had a Carter lift pump and a Bosch 975 main pump and it used to have a few hot fuel issues with petrol .

I also remember once wondering what would happen if a FPR was T'd off before the fuel rail and returned the fuel from before the rail not after it . In theory the rails still pressurised but all fuel in it can only exit via the injectors . Isn't this how late cars work only with a dumb (non manifold pressure referenced) FPR in the fuel tank ? May make for interesting hot starts !

Also I've been looking at pics of the Nismo drop in pump and it looks very much like a Z32 VG30TT one with the bracket made to suit OE rubber mounts . For 300+ RWKW these are probably a no brainer and OE Nissan Japan gear tends to be pretty good , its just the Scrooge in me wants to know if there is a slightly more "cost effective" solution .

Also before I go these OE pump speed controllers , did R33 GTRs use "three speeds" where the GT25Ts had two ? I run a Vipec plug in and a 33GTR pump and I don't think I've heard its tone change except when the engine is close to stalling revs . Then it sounds like it slows down which can't be good . I think a battery supply rewire is needed here .

Sorry so many cheers A .

Sydney Kid posted a thing that you can wire to your airflow meter as voltage increases it allows more current to the pump. This however im not sure how it would work with Vipec I have a vipec too and would like to know how i can vary the voltage received by the pump depending on how i drive. Another option would be a fuel cooler but i dont see them being very effective for temp drop, they do help though

  • 2 weeks later...

I'm just going round in circles ATM wondering what to do fuel pump wise , need it to live with E70 and it seems some fuel pumps may not be long term reliable with these high ethanol content fuels . Fuel pumps are lubricated by the fuel and ethanol alcohol obviously doesn't do it as well as ULP so I guess roller cell pumps won't live as long .

I'm going to start a thread on those Walbro F90000267 E85 compatible pumps .

A .

Sydney Kid posted a thing that you can wire to your airflow meter as voltage increases it allows more current to the pump. This however im not sure how it would work with Vipec I have a vipec too and would like to know how i can vary the voltage received by the pump depending on how i drive. Another option would be a fuel cooler but i dont see them being very effective for temp drop, they do help though

Lowering the voltage to the pump will cause the current draw to rise, and perhaps cause the pump to stall/burn out. The voltage needs to be 12V minimum and switched as a square wave input (PWM) for the pump to last imo, although the Vipec could control a solid state relay at that frequency just fine at a guess.

my Nismo pump is quite noisy. Almost sounds like a dremel or shaver enclosed. But its only loud when its full and the buzzing lasts all the way to 1/4 tank.

Nismo is pretty damn quiet. Yes, it louder than an OEM unit, but not like a 044.

Something is touching somewhere and Vibing on it. Once the tank gets down there isn't as much fuel to move the pump around?

Funny, my 044 is the opposite. Much louder at 1/4 tank.

Mates have used nismo drop ins for years with no hassles as a lift pump to there surge tanks. Althou a wqlboro off scotty mn35 would be a better pump for e85 as well as cheaper.

Josh

Edited by Joshbigt62r

Quick question, mightve been answered before but I didn't want to start another thread, is the nismo pumps e85 compatible?

im pretty sure Nismo also considered race gas in their RnD. Besides Nismo over engineer everything they make i doubt E85 would cause you any problems.

I hope so. . Ive contacted an ebay seller about this and he said nismo couldnt give him a straight answer as to wether it would be okay on e85 or not

But yet again another(big name) retailer with his listing for a nismo pump for a r34 gtr states" not compatable with e85" !

Edited by StevenCJR31
  • 2 weeks later...

Thought I'd post in this topic rather than start a new one as my query is reasonably relevant to the conversation, but when installing the Walbro 450LPH pumps does the choice of sock have any influence over the flow? I'm assuming not otherwise they wouldnt have supplied two but I'm wondering whether using the smaller sock would impede the flow at all (pic attached).

The smaller sock seems to fit nicely into the bottom of my cradle so would prefer to use that. If it negatively influences flow though will use the larger of the two.

Cheers

post-132-0-09744100-1378603768_thumb.jpg

Just to bump this a bit - in the attached pic I've positioned the fuel pump in the cradle as I would like to mount it (upright - got the idea from trustr32 on here).

I'm just concerned that the sock might be too small? The pump is a Walbro 450lph unit as mentioned above. Does anyone think the size of the sock will cause any restriction problem? It does sit very nicely right in the bottom of the cradle which is why I'd like to mount it like this.

post-132-0-27429300-1378723262_thumb.jpg

I think u are on a winner with that setup as it also sits in the lowest part of the cradle and is really not much smaller than the oem sock.

What brand sock is that and what is the ID of the sock fitting?

That's what I was thinking, sits right down in the lowest part of the cradle. I'm not sure of the ID but it came with the pump so I'm assuming it's a Walbro branded sock. Maybe I'll just chuck it in and see how it goes - should be ok I suppose! :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...