Jump to content
SAU Community

Recommended Posts

How would XR6's be legal then? :mellow:

because they are an australian car brah.

or maybe, just maybe, it is because the restrictions are based off power to weight ratios (or just outright power in some states), the target value being under about 120kw/ton. the 350gt comes in well over this number since it's power output is 206kw (compared to the falcon's 195kw) and it weighs about 300kg less than the 1700kg falcon (based of the FG which comes in at 114kw/ton - the highest for any natro 6 cylinder falcon). in qld though the car must be under 200kw (plus non turbo, etc). this actually rules out the sv6 commodore, since it has 210kw, although it is right on the limit for some other states using the power to weight ratio rule.

  • Replies 165
  • Created
  • Last Reply

Top Posters In This Topic

Well NSW has the restrictions:

NO turbo

NO 8 cylinders or more

plus the following 6 cylinder vehicles

  • BMW M and M3.
  • Honda NSX.
  • Nissan 350Z and 370Z (including private or 'grey' import variants eg. Infiniti G35, Infiniti G37, Skyline 350GT (V35), Skyline 370GT (V36)).
  • All Porsches from 1994 models onwards (except diesel).
  • Mercedes Benz SLK350.

if you do the calculations you will find that pretty much all cars have a power to weight ratio of higher than 120kw/ton (which is what the old rule used to be. obviously they decided to change it to a simple list of restricted cars to stop people complaining because they put their car on the dyno and it made less than 120kw at the wheels so they should be able to drive it.

The smartest thing to do is rip all the things that contribute to the heavy weight of the vehicle. I mean, take out the sound-deadening, carpets, spare wheel. Remove the air-con unit, take all the glass out and just have nothing. Take the wheels and engine out of the car too and it will probably be faster than it was before.

actually fg xr6 goes really hard. my friend has one (auto), it completely demolished my NA R34 from second gear onwards after i dropped the clutch in 1st gear.

What do you expect? You're comparing a milk bottle to a wine cask.

Also, the XR6 is a family car. I'd buy one to tow my 32 to the drifts and take my grandmother out to lunch in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...