Jump to content
SAU Community

Recommended Posts

  • Replies 149
  • Created
  • Last Reply

Top Posters In This Topic

nah its not. no blue smoke at all.

i can actually see its coming from the filter area.. just not sure exactly where.. might degrease the whole lot a couple of days before the next service to see where it is..

turbo's getting fixed once we finish scottys GTX i got a cheap quote from Hypergear so will get it done!

and if theres anymore problems im gonna buy scottys or another stock one and start again.. what choice would i have.

Hey Aaron, I hear Craig's got a good one for sale :P

Why go Hypergear? Don't want to go GTX?

Does the HKS filter have the magnet in it? Time to get ready for my next service I think, stacked on the K's since I got it!

why would i want craigs? mine puts out more power nyaanyaa.gif and im not even tuned properly yet...

i only need a bigger wastegate, ive got a stage 2 sierra and its boost creeping up top.. proves our housings are good!

i take it u dont know much about my car in particular lol

Its not the turbo's fault, or the car really. The banjo bolt restrictor would have been partially blocked in Aaron's car causing the bearings to fail. Can you imagine how easy it is to block a 1mm hole with crud? I bet most of the turbo failures have been caused by oil starvation as im running 19psi on the stock turbo for 3 months now without an issue, and at 225kw so the shaft speed is right up there...

buy craigs because its broken down less and killed fewer turbos :P

How is craigs broken Down less? His is broken more than all of us. Remember he does have a different engine coz he brokeded his other one.. Not to mention the trabsmission flaring through every gear..

Stop trying to sell the mexicans your dodgy yank products we all know anything the yanks make don't really last

Yep, Carlton. "Melbourne Business School".

Hangman's Tour at the Gaol tonight. Gonna bag me a ghost!

BTW I did actually as a question related to this thread, that got lost in the bullshit... does the HKS oil filter have a magnet in it? I'm running the Nismo at the moment and will be due for a change soon.

Yep, Carlton. "Melbourne Business School".

Hangman's Tour at the Gaol tonight. Gonna bag me a ghost!

BTW I did actually as a question related to this thread, that got lost in the bullshit... does the HKS oil filter have a magnet in it? I'm running the Nismo at the moment and will be due for a change soon.

ghost tour is awesome!

yeh the HKS has a magnet in it..

  • 2 weeks later...

got around to fixing my oil leak yesterday.

drained the oil, pulled off the filter.

used a 22mm deep socket to get the plate off.

I dunno if it is just mine, but it was close to being blocked with a whole bunch of gunk. as if the oil have become almost greasy mud. to be honest i dont how oil was actually travelling through..

any way.. cleaned it all up ended up talking almost half a palm full of gunk out.. put it all back together with a new Greddy filter. and filled it with sougi.

once the car was warm enough after about 10-15min of driving, i gave it some Gas.. and found out my tunes is all over the place again and lean? didnt think it would make this much of a difference..

being cleaned i know ive free'd up the oil flow alot and the engine obviously. and at Idle, the car sound 200% better than it did 3 days ago.. and every other time i've done a service...

this could also be half the reason my turbo kept blowing lol

what is everyones thought? perhaps you should all check yours???

Cam/Craig/Iain: Please dont take the piss out of this my uncle just died so im really not in the mood.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...