Jump to content
SAU Community

How Do You Sense Your Shift Points.

Borci88
 Share

  

93 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

  • 2 weeks later...
jjman Mentor

jjman

Posted
Posted (edited)

tacho mate. Maximum tune style lol

:thumbsup:

IMO unless you do this then you are either limiter bashing or not getting peak HP.

otherwise if you are just cruising around then why would one need anything other than just a general feel. Doesnt really matter if it goes to 2800rpm or 3500rpm at 1/3 throttle really does it...? But thats not really the scenario for this quesiton is it?

Edited by jjman
Miguelone Grand Master

Miguelone

Posted
Posted (edited)

I use to use feeling, but since i just got my skyline and have only driven it once, i used the taco and feeling, only until i get a feel of things

taco.jpg

Edited by Miguelone
iseekool Veteran

iseekool

Posted
Posted

R34 in tiptronic mode - usually 4000rpm to 6000rpm. Driving easy auto shifts around 2000rpm to 2500rpm

IS200 (manual) - I generally shift on sound and feel, except on steep hill starts - I use the tacho. Normal driving shift around 2500rpm to 3200rpm. Down hill I shift at 1800rpm.

Datsun bluebird - 4000rpm

Peter89 Proficient

Peter89

Posted
Posted

I tell usually by sound at lower gears and tacho at higher gears, and in practice (on the street) I always short shift before 5000rpm. I probably exceed 5000rpm about once per week at most (daily driving). Can't remember the last time I went past 6000rpm, on the street it just isn't required (theoretically it would be required for a drag race).

On the street in 1st and 2nd gear with any sort of corner I short shift to get into the next gear so I can ride the torque wave through and out of the corner. This means precise throttle modulation is less of a factor and it saves a gear change and means less wear(2nd has more power but can't usually put it all to the ground). Adding bumps into the equation in Sydney just makes it even more relevant.

Just cruising I change at the point the revs start at 2000rpm -2200rpm in the next gear....or what feels right.

what's the point of having the car if you don't gun it a few times per drive?

Might as well drive a kia :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      WGNC34 - floor mats

      By GTSBoy · Posted

      I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • MBS206
      R34 Skyline climate control unit transistor

      By MBS206 · Posted

      Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Murray_Calavera
      Tein Circuit Master- rebuild worth it?

      By Murray_Calavera · Posted

      Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • Duncan
      NC MX5

      By Duncan · Posted

      I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
    • Duncan
      WGNC34 - floor mats

      By Duncan · Posted

      Basically, if there is a part# on the nissan catalogue, it is a genuine part. There is a thing called "new old stock" which is stuff made years ago but never sold (or landfilled), but it is super hit and miss what you can buy. Other than some expensive Nismo stuff there is nothing new being made that suits these cars. The only time to be a little careful is (mostly in the US I think, but maybe Japan too), Nissan started rebranding some cheap crap maintenance parts like oil filters as "Pitworks"; stay away from them, if you are buying cheap just buy whatever the local car parts shop carries The three part numbers have an explanation on Amayama: 0V005 is auto, base style 0V015 is manual 0V505 is auto, hectic momo branded ones, maximum F&F points there!
×
×
  • Create New...