Jump to content
SAU Community

Questions On M35

Sydsyd

By Sydsyd,
in Four Door Family & Wagoneers

 Share

Recommended Posts

QJQ Enthusiast

QJQ

Posted
Posted

1. ARX rims are 18 x 7.5 JJ, +40 offset.

2. I don't have any recommendations for tyres yet but the tyre placard says 225/55 R18 97H, although my ARX has 235/50 R18 101V (these came with it when I bought it). Having said this, when I upgrade my wheels I'll be looking at a larger rolling diameter to hopefully correct the speedo and maybe even improve the fuel economy.

3. In the "M35 - Light Changes" thread M35 - Light Changes recently Duncan (Dunc) posted a photo of the indicator bulb. Basically it is a larger version of the parker (T10). I think they are known as T20 and it should be 21 watts as specified in the handbook. I'm fairly certain the rear bulbs are the same as the front.

Cheers

  • Replies 193
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

bigkevracer Grand Master

bigkevracer

Posted
Posted

Those T20s are bloody massive - might be what Dunc was talking about. This kind of thing: http://www.ebay.com.au/itm/T20-Amber-Front-Indicator-Blinker-Lexus-ES300-2001-2009-/320644252369?pt=AU_Car_Parts_Accessories&hash=item4aa7e302d1#ht_5621wt_922

Similar fittings...

andy65b Veteran

andy65b

Posted
Posted

Hi chaps..

Question - Does anyone know if the VQ25DET turbo to dump gasket is the same as the RB26s? Will install a new system soon and need to know.

Cheers all..

Generally the stock one will go the distance. It is good quality and still using the stock one after turbo change 4.5 years of driving.

Commsman Veteran

Commsman

Posted
Posted

Generally the stock one will go the distance. It is good quality and still using the stock one after turbo change 4.5 years of driving.

+1. I think mine looked perfect when it came out but put it back with a smear or hi temp silicon on both sides just to be sure.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

High temp silicone will go hard and brittle on the turbo housing Leon, I only use it if the flange wont seal now.

As there is no real pressure after the turbo the gasket isnt critical, it should be fine even if its cracked. Our turbo outlet gasket is VQ specific and was only on the VQ25det's and VQ30det's, you will need to go through Nissan for that one.

The pre turbo gasket where it bolts to the manifold is a standard T3 gasket and should be replaced whenever the turbo is removed with a good multi layered stainless gasket. Pressures in the manifold can be quite high.

joshm35 Veteran

joshm35

Posted
Posted

Part number for the turbo gasket is 14445-4P200 in case you need it. For reference it was only used on Stagea (VQ25det) and F50 Cima (VQ30det)

This may help.

http://justjap.com/store/product.php?productid=20105&cat=&page=1

Commsman Veteran

Commsman

Posted
Posted

High temp silicone will go hard and brittle on the turbo housing Leon, I only use it if the flange wont seal now.

I hope not! I'd be royally peed if I have to remove the dump again. But I had a look at the packet & it's temp rated for turbos.

In any case, it was only a smear, more to hold it in place than anything else. It all seems OK till now & been on for a while too - see what happens in the next few years.

Sydsyd Collaborator

Sydsyd

Posted
  • Author
Posted

i have a spare for each end, but im pretty sure you can buy new ones. if you get stuck let me know, id really rather sell both as a pair or with the spare rack i have

how much u sell the pair for?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...