Jump to content
SAU Community

Rich + More Ignition, Or Lean + Less Ignition, What Is A Safer Way To Tune?


Recommended Posts

What does MBT stand for?

mean best torque

the point at which, as you advance ign timing, the engine makes the best torque.

say at 3,000 rpm and 10deg timing, the engine makes 200nm, 12deg might make 205nm, 14deg makes 207nm, then 16 deg makes 205nm, then your ign timing for MBT is between 14 and 16deg.

happy to be proven wrong, thats just how I understand it...

P.s. for the mathematically minded fellas out there, I've always struggled with understanding the relationship between power and torque...

I know the power is the amount of work done with respect to time, and that torque is a rotation force, but dont understand how they interact!?

If is accurate to say that torque is the derivative of power with respect to engine RPM???

Edited by StealthX

mean best torque

the point at which, as you advance ign timing, the engine makes the best torque.

say at 3,000 rpm and 10deg timing, the engine makes 200nm, 12deg might make 205nm, 14deg makes 207nm, then 16 deg makes 205nm, then your ign timing for MBT is between 14 and 16deg.

happy to be proven wrong, thats just how I understand it...

Is it always the case that torque will drop off after MBT if you keep adding timing?

I was of the impression that it would just stop making any more torque.....I'm guessing it might be dependant on the set up itself?

P.s. for the mathematically minded fellas out there, I've always struggled with understanding the relationship between power and torque...

If is accurate to say that torque is the derivative of power with respect to engine RPM???

Power is directly proportional to torque x rpm.

Think of torque as the instantaneous force, rpm is how many times a second that force is being put out, hence why your power can still increase even though torque is decreasing.

Another analogy is torque is the force of each cylinder explosion, rpm is how many explosions per second. So if you have lots of explosions but they are weak (low torque, high rpm) or not many explosions but they are very powerful you can have the same power (high torque low rpm).

P.s. for the mathematically minded fellas out there, I've always struggled with understanding the relationship between power and torque...

I know the power is the amount of work done with respect to time, and that torque is a rotation force, but dont understand how they interact!?

If is accurate to say that torque is the derivative of power with respect to engine RPM???

relative power = torque x rpm

basically if you have a perfectly flat torque curve from 0 rpm to redline (never happens, i know, just an example) the power will double when you double the rpm. so if your making 100kw at 2000rpm, you'll be making 200kw at 4000rpm, 300kw at 6000rpm and 400kw at 8000rpm etc.

torque is the force that is exerted by each combustion cycle, power is the overall force produced by the engine (as revs increase each combustion might be less powerful on its own but its happening faster, therefore more combustion cycles in a set period of time).

Is it always the case that torque will drop off after MBT if you keep adding timing?

I was of the impression that it would just stop making any more torque.....I'm guessing it might be dependant on the set up itself?

Yeah not sure on that one... I was under the impression that more ignition timing past MBT will make more heat, thus less dense intake charge and less power. sorta like a turbo out of it's efficiency range. boost = timing and power = torque.

Power is directly proportional to torque x rpm.

Think of torque as the instantaneous force, rpm is how many times a second that force is being put out, hence why your power can still increase even though torque is decreasing.

Another analogy is torque is the force of each cylinder explosion, rpm is how many explosions per second. So if you have lots of explosions but they are weak (low torque, high rpm) or not many explosions but they are very powerful you can have the same power (high torque low rpm).

right! got it....

thanks!

MBT is actually maximum brake torque, or peak torque, i.e. the peak of the torque curve. After the point where the maximum amount of torque can be achieved cylinder pressure drops, ideal for more timing to be added to continue to make power.

If you look at many stock ignition maps (not stock PowerFC maps) you will see after the peak torque, igntion timing will increase. Do a trace map on a stock ECU for any newish car and you'll see after MBT, more timing is added. A good example would be a 4G63T map.

I guess that's just my opinion though. Jez I will need to send you another email BTW! You may be disapointed, may not haha.

look out guys we have a trader among us. First of all he was putting a toyota motor in his skyline. But now he is buying a silvia with sr20.

All good im an ex silvia owner. :ninja:

a couple of points. the formula for Power is torque in ft lbs x rpm over 5252, this gives power in hp. secondly adding timing after peak torque does not increase EGTs in my experience. if anything it lowers them. even when detonation occurs they will keep dropping, altho damage will obviously occur.

It makes sense for timing to always reduce EGTs as you are keeping the explosion in the cylinder for longer so more heat gets absorbed.

Edited by Rolls

I use both too, its the only accurate way to see whats going on isnt it? Im sure most tuners would prefer to have them in the dash if possible. I used to run the egt sensor in the dump and noticed a 100 degree increase in temps now its in the manifold.

When tuning last month I noticed as we increased boost past a certain point the power didn't increase but torque continued shooting up, how can this relate to your equations?

Thats because torque is on a finer scale the whole way through, its why I prefer to tune to MBT using the torque curve - its easier to spot differences. Its also way torque curves often tend to have huge dips etc if the dyno software allows you to scale to just minimum torque to max torque, instead of 0-max torque.

Its not an explosion Rolls. Its a burn

its actually a deflagration ; )

(I knew)

I use both too, its the only accurate way to see whats going on isnt it? Im sure most tuners would prefer to have them in the dash if possible. I used to run the egt sensor in the dump and noticed a 100 degree increase in temps now its in the manifold.

When tuning last month I noticed as we increased boost past a certain point the power didn't increase but torque continued shooting up, how can this relate to your equations?

That is because peak hp isn't at peak torque. So you might have had more tweaking around peak torque to do, but not at peak hp.

Edited by Rolls

The engine will give you the answer. We have tried tuning lean with minimal timing but running it at low 11's with more timing doesnt make much difference to our car. A richer tune will leave more room for safety unless its on the ragged edge with timing.

Most RB's i have seen that are running 20+psi have always liked to be tuned in the mid to low 11's

  • 2 years later...

Just dial in timing till the motor stops making power or knocks for a certain rpm, then proceed to next rpm band.

Joys of e85, keep pumping in timing till the power drops as it doesn't knock.

Joys of e85, keep pumping in timing till the power drops as it doesn't knock.

I have almost the opposite opinion, more boost, 11:1afr and keep the timing on the lower side of MBT for best longevity, especially at the point the torque hits hard.

E85 knocks just like petrol but at a much higher boost. Definitely need knock ears on the block for WOT tuning...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...