Jump to content
SAU Community

Recommended Posts

lol @ hearse cruise just don't show ya pussy scared of some keyboard flamage?

You'll feel out of place if u don't attend with the wasteland crew.. Almost need something to identify the cool cats

On seats I like my bride and for $600 second hand in immaculate condition good value to

I wanted to, atleast for sunday.. but theres a stagea cruise, and i kind of said I was going lol i tried to make it a cruise to the sns, but they wont listen lol

thats why you should have made it 6th and you organised it so who is to blame

you kunts have to back me up lol

http://www.skylinesaustralia.com/forums/topic/381137-vic-stagea-cruise-plan/page__st__20__gopid__6082346#entry6082346

Mick, it had to be the date with most votes. lol unfortunately out of my control.

BP Petrol Station on Warrigal Road.

Just off the Monash freeway near Chadstone. 6:25-6:35am

Join your fellow wastelanders.

dont do the BP. harvey norman just up the road has more room and is less busy at that time. thats where all the GOR cruises used to leave from (eastside premeets anyway)

dont do the BP. harvey norman just up the road has more room and is less busy at that time. thats where all the GOR cruises used to leave from (eastside premeets anyway)

I did think about and did mention that, becuase I have been there and it is quite small.

But the other guy wanted to and I think there won't be that many cars there at 6:30a.m on a Sunday morning. And there should only be a few of us.

Plus the cars can fill up on Petrol and wash their cars there if they want.

SHouldn't be busy, who wakes up that early on a Sunday morning on a semi long weekend :unsure:

I did think about and did mention that, becuase I have been there and it is quite small.

But the other guy wanted to and I think there won't be that many cars there at 6:30a.m on a Sunday morning. And there should only be a few of us.

Plus the cars can fill up on Petrol and wash their cars there if they want.

SHouldn't be busy, who wakes up that early on a Sunday morning on a semi long weekend :unsure:

what time is everyone leaving then? and its raining.. not much point in washing lol i might just attack mine with a pressure hose.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...