Jump to content
SAU Community

Recommended Posts

no idea man. just got it off the trailer and parked it. gonna pull it under the car port tomorrow arvo and give the interior a good clean/ remove the driver side bride seat. which is f**kn rubbish.

interior work i noticed that needs to be fixed.

replace GTR rear seat with factory 4 door seat

replace bride with GTR driver seat

replace dash, carpets, leather boots, driver side door trim.

exterior

repair front bar.

engine- new engine lol.

expecting this to end up costing a fair bit but im keeping this so meh... didnt pay much for it anyway so cant really go wrong

Nice rims if they are te37s! But these boys will say not enough offset for a Gtr. Cas' car has 18x9.5 +12 and its flush

Not TEs unfortunately, didn't want to spend that much. They are brand new though, and few if any people will have them in Aus.

It's not enough for a gtr, but I have a gtst so should be alright

no idea man. just got it off the trailer and parked it. gonna pull it under the car port tomorrow arvo and give the interior a good clean/ remove the driver side bride seat. which is f**kn rubbish.

interior work i noticed that needs to be fixed.

replace GTR rear seat with factory 4 door seat

replace bride with GTR driver seat

replace dash, carpets, leather boots, driver side door trim.

exterior

repair front bar.

engine- new engine lol.

expecting this to end up costing a fair bit but im keeping this so meh... didnt pay much for it anyway so cant really go wrong

geez that requires a lot of stuff to be replaced,

why didn't you just save for longer and buy a running one, would be cheaper then to get this thing driving

haha birds

guys i didnt do a search, but how hard would it be to get a RWC if i dropped a 25DET into it instead of another 20det?

25det, you'll need engineers cert, means upgrading the brakes while you're at it...

Whats wrong with the motor?

25det, you'll need engineers cert, means upgrading the brakes while you're at it...

Whats wrong with the motor?

No comp in cylinders 5&6

And rb20s are gay.

I'm taking my time with this. So might as well paint the engine bay etc when the 20 is pulled out

Roman, want some period correct wheels for this bitch.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...