Jump to content
SAU Community

Recommended Posts

Xbox has the same problem, CPU and GPU heatsinks don't stay clamped down enough and vibrations + heat make the components seperate from the motherboard over time. You can also fix an Xbox by putting it in the oven, but it doesn't always work and you can easily damage the other components on the MB. It fixed my mate's Xbox, though afterwards, his Xbox would occasionally freeze with intense graphic gameplay. Ash's mate reckons $85 but not guaranteed to fix...they use a rework station though which is much safer than ye olde oven lol.

lies, ghetto fixes are always the best

just got back from my first proper ride. still alive!

did ~60ks

hit ~130 on the freeway, was freezing! felt like my chest was being punched in...

wrists raped

talked so much shit to myself i ate most the insides of my mouth/cheeks, gets lonely...

at 100km/h bike sits at just under 9k

/bikes

Ride on Sunday may be a go ahead now...bike is getting serviced this morning, hopefully pick up around midday :)

And yeah you spend a lot of time talking to your helmet, mostly about how bad drivers are.

just got back from my first proper ride. still alive!

did ~60ks

hit ~130 on the freeway, was freezing! felt like my chest was being punched in...

wrists raped

talked so much shit to myself i ate most the insides of my mouth/cheeks, gets lonely...

at 100km/h bike sits at just under 9k

/bikes

It does take a fair bit of energy out of you, even though u guys are buff kents as well, I'm the smallest with heaviest bike :(

Ride on Sunday may be a go ahead now...bike is getting serviced this morning, hopefully pick up around midday :)

And yeah you spend a lot of time talking to your helmet, mostly about how bad drivers are.

Make a thread? :) <3

mostly about how bad drivers are.

Was on melton hwy doing the speed limit this a$shole gets up my arse starts flashing his lights, got out of his way/showed him my finger. 5 seconds later I pull up next to him at the lights, gave him a clap congratulating him on getting so far ahead of me, didnt even have the balls to look my way

On my way home exiting the freeway I stalled the bike taking off uphill at the lights, mint chick stops behind me to make sure I dont get rear ended by someone speeding up the ramp eventhough I waved her to go round, waited there till I got the bike going again.

Moral of the story - there's bad/good drivers just hope I dont come across the bads often

/

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...