Jump to content
SAU Community

Recommended Posts

oh those rays wil look mint. a quick google turns us ozft86 forums where you'll find a thread on taillights. apparently CarX in Clayton or somewhere will do a clear vinyl. looks the goods. hunting for a mate who also has a white ft (on order)

Get your mum some batteries for her vibrator while you're at it

ehJcXHM3_original.png

nah mang, fathers day.

Stim U – Oral

SRP $17.95* - today just $9.99!

Masturbation device for men that simulates the ‘Oral’ position

Pre-loaded with lubrication for instant use; lotion reservoir keeps point of insertion in perpetual wet state for your enjoyment.

Discrete Nationwide Delivery!

For male self-stimulation you can’t beat this Stim U - Oral which simulates the ‘Oral Sex’ Position for a male. Its new and improved design fulfills your ultimate deep throat fantasy which is achieved by combining the curve in the mid-section and a special one way air valve on the silicon sleeve to create a vacuum effect. The air hole on the top has a removable seal allowing you full control of the tightness level. And another great bonus of this wonderful device is the sucking sound created from the suction effect. The Canisters are pre-loaded with lubrication for instant use. While the clever lotion reservoir keeps point of insertion in perpetual wet state for your enjoyment.

Features:

  • Stim U – Oral
  • Masturbation device for men
  • Simulates the ‘Oral’ sex position
  • Design fulfills your ultimate deep throat fantasy
  • The air hole on the top has a removable seal allowing you full control of the tightness level
  • Bonus sucking sound is created from the suction effect of device
  • Convenient 16cm size
  • Canister comes pre-loaded with lubrication for instant use
  • Lotion reservoir keeps point of insertion in perpetual wet state for enjoyment

image1.jpg

*SRP was supplied by the manufacturer & was true & accurate as on 30/08/2012.

oh those rays wil look mint. a quick google turns us ozft86 forums where you'll find a thread on taillights. apparently CarX in Clayton or somewhere will do a clear vinyl. looks the goods. hunting for a mate who also has a white ft (on order)

There's a red 86 that was at both JDMST meet and HardTuned meet, had his taillights done by CarX. Let's just say, Id keep my money in my pocket.

Destroy VX SS in a rolling...he does loser fly by as I go heavy on the brakes and a VE SS playing catch up on us both flies through the 10 metre gap between us at ~150km/h, then nearly loses it around the upcoming corner, farkin nutjob!

where was my invite brah!

expendables 2 pretty good, funny and action packed

where was my invite brah!

expendables 2 pretty good, funny and action packed

Was on the way home from the gym :P

We should do a rolling at the moment though, while we both lack grip! Then I might stand more of a chance against you...

Until E85 tune...come at my wallet Rape Pace!

Jackie-Chan-Meme.jpg

Pic didn't work so I don't know your real reaction, now I'm just confused and scared and Inquisitive all at once. Thanks hamish. Thanks. My life is over now that I can't see that meme. It's just over lol

ok... i'll try again...

3p3wrx.jpg

Oh. Lol nah because the gtx is external gate four inch housing blah blah blah.. But this is the standard two bolt snout and housing with the internal gate 5 bolt, so in under the mess of manifolds pipes and hoses, it looks stock

Or more stock than it does

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...