Jump to content
SAU Community

Recommended Posts

can someone scan their motor magazine and post pics?

Got a few modded fords and holdens too

One of the fords had 558rwkw. Yet still a few seconds slower than a 100rwkw 86 :P To be fair its a small track

o8lVFs0y_original.png

LOL had to look twice at that before i realized.

Got a few modded fords and holdens too

One of the fords had 558rwkw. Yet still a few seconds slower than a 100rwkw 86 :P To be fair its a small track

haha yeah ofcourse it would do shit on a small track! Wonder what it would do around PI :P

Those kws are for dyno queening

Yeah pretty much or drag spec, assume its the 5.0l coyote?

So the s3 is good? Full review please. I'll consider buying your bike

Not sure if serious

Was that 3? My 4 has been only phone to last me 2 years with zero problems I use my phone flat out to

Had 3 and 4 both froze a lot as well as other issues

Hooked on frontline commando sick game and works perfectly on my android

A+

Will sus it out, I'm over temple run

friend asked me to go get motorbike license with him in a couple of weeks >,<

tempted!

Do it.

And buy my bike

<3 varrstoens

273037_381936251876746_1052533594_o.jpg

Dooo ett! Matt black. kgo

haha yeah ofcourse it would do shit on a small track! Wonder what it would do around PI :P

Yeah no doubt. Disappoint with the 86 1/4 time though. 13.98 with 168rwkw.

Dooo ett! Matt black. kgo

Yeah no doubt. Disappoint with the 86 1/4 time though. 13.98 with 168rwkw.

Haha only issue is apparently they dont clear brembos in the sizes I'm looking at.. I dont have brembos yet but was looking at them down the track.. hrm.

And yeah, light stiff car = hard to get power down not designed for drags I guess

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...