Jump to content
SAU Community

Recommended Posts

these will be too big man. wayyy too big..

how is it gayer than mohsen? i enjoy the fact i dont have to be scared of being defected when I drive now.

Ric I didnt even know you had a car til after SNS.. that makes you gayer than mohsen.

these will be too big man. wayyy too big..

how is it gayer than mohsen? i enjoy the fact i dont have to be scared of being defected when I drive now.

Ric I didnt even know you had a car til after SNS.. that makes you gayer than mohsen.

You being unaware has no bearing on my sexuality brah

My car is mad

Finished exams yesterday so today I've started work on the gtr again.

Woke up nice and early in the morning, got all the nuts off the plenum

and a few hoses that hadn't been removed yet. Timing belt is off also.

Task is to remove plenum in the car, to my understanding it involves a lot

of swearing but I never thought this much..

How the fu(k do I take this mother of a plenum off? I've unbolted the air

chamber underneath and still no luck. Is it easier to pull them off the throttle

bodies or easier to pull both out together? I can't see seperate nuts/bolt heads

for the tb's so I'm assuming it's just long as studs coming off the head through

the plenum flange.

God and sau help me

Parents cheaped out on you and bought you imitation Lego. Or Duplo, which was Lego for tards.

Had lego lego, had the mates an stuff, just had an imagination and didnt need to be told what to make :P

3 months back I bought the Super star destroyer Ultimimate colletor series

over 4 foot long and over 3000 peices.

http://lego.wikia.com/wiki/10221_Super_Star_Destroyer

instructions come in handy.

not building it till I get a bigger place as no-where to put it atm

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...