Jump to content
SAU Community

Recommended Posts

Adding to the VicRoads rip off saga...

Just replaced spark plugs in car...it runs 63 times better...10,000km is too long for copper plugs in a modified car methinks. Though that interval was more out of procrastination.

The only reason I let mine stretch to 10,000km sometimes is because of the bloody RB crossover pipe and not wanting to scratch up my pretty valley cover paint if I don't remove it (+20 minutes) to the job.

I remember my old ford laser... Pop off the leads, unscrew plugs, screw new plugs in, cry because you drive a ford... Finished in 5 minutes

That awkward moment when your housemate receives a letter in the mail from the Australian Federal Police.

those guys hardly deal with misdemeanors or misunderstandings. I wonder if it also deals with Immigration issues, or would the Department Of Immigration just deal with it? maybe terrorism or illegal visa. hmmmmmmm *curious*

The only reason I let mine stretch to 10,000km sometimes is because of the bloody RB crossover pipe

This

It's a 30 minute job that should be 10 minutes.

And working with old hoses and screws, I'm ultra careful about the way everything goes back.

I leave the valley cover off, so I can do 5 of 6 plugs without touching the pipe. But Nissan Y U put crossover pipe slightly too far over the 4th cylinder? If I had uni-joint sockets I could do it, but don't really like using those unless I have to.

Can't get started, Chemical Heart... Every time I get started, you pull me apart.

Old Grinspoon is the best Grinspoon

dead Grinspoon is the best Grinspoon

Just replaced spark plugs in car...it runs 63 times better...10,000km is too long for copper plugs in a modified car methinks. Though that interval was more out of procrastination.

I ran BCPR7ES gapped to .9 and used to change every 20,000, even when changed they worked fine and looked 100%

dat trent tune

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...